Getting started
l. Open the battery compartment of receiver and insert the two AA batteries.
2. Open the battery compaflment of transmitter and insert the two AAA batteries.
The Remote ChekrM needsthe receiver to register the radio frequencl signal from the transminer. This needsto be done every time the unit is operated after the unit is turned off.
Automatic registration
l.Plug the two stainlesssteelprobe sensorsinto Sl and 52 on the transmitter.
2 . Slide the switch on the rear of the receiver to OPERATE . REMOTE SENSOR I and
3 . Slide the switch on the rear of the transmitterto ON . This needsto be done within 60 secondsof turning the receiverto OPERATE in order for the receiver to automatically register the signal from the transmitter.
,1. Registration is complete when the unit beeps. REMOTE SENSOR I remain on and rhe temperaturefrom probe sensor I is shown under PROBE TEMP.
Note: The receiverwill automaticallyexit the registrationprocessafter 60 secondsand return to normal mode. If registrationis not completeREMOTE SENSOR I will not be shown and
Manualregistration
1. Plug the two stainlesssteelprobe sensorsinto S1 and S2 on the transmitter.
2 . M a k e s u r e t h e s l i d e s w r t c h o n t h e r e a r o f t h e r e c e i v e r i s s w i t c h e d t o O P E R A T E a n d t h e s l i d e s s i t c h o n r e a r o f t h e t r a n s m i t t e r i s O N .
3. PressSET on the rearof the receiver.REMOTE SENSOR I and
4 . Pressand hold TX for 2 secondson the rear ofthe transmitter .This needsto be done uithin 60 secondsofpressing SET on the rear ofthe receiverin order for the receiver to register the signal from the transmitter .Once TX is releasedit will take several secondsfor the receiver to register . If it doesn'tbeepwithin
5. Registration is complete when the unit beeps.REMOTE SENSOR I remain on and the temperaturefrom probe sensor I is shown under PROBE TEMP.
Displaytemperatureof remoteprobesensor1 & 2 andautoscroll
I . PressSl/S2 to toggle the temperaturedisplay underPROBE TEMP betweenREMOTE SENSOR I and REMOTE SENSOR 2.
2 . Press and hold Sl/S2 for 2 secondsand the display will auto scroll every three secondsbetween REMOTE SENSOR I and RF - \IOTE SE\SOR 2 temperaturedisplay.Pressand hold Sl/S2 for 2 secondsagainto stop the auto scroll.
Note: You can remove probe sensor2 from the transmitter52 plug in and insert into the 52 (Direct Plug in) ol'thereceirer. The displal shous SENSOR 2 onl1. as it is no longer a remotesensorpluggedinto the transmitter.
Meat selection
PressMEAT to selectmeat type. BEEF, VEAL, LAMB, PORK, CHICK (chicken)or TURKY (turkey).
Taste selection
PressTASTE to selectthe level of donenessfbr the meat type selectedW. . DONE (well done),MEDIUM. M. RARE (mediunrrare)or RARE.
Note: The temperaturedisplayed under SET TEMP will show the preset temperatureaccording to USDA temperaturctable (TABLE A) for the level of donenessselectedExample:.Beef will be Well Done at 170 'F.
Set temperature
PressA or V to raiseor lower the settemperatureThe. box aroundthe TASTE levelsdisappearsThis. will not changethe presettemperaturesofTable A or B. Pressing
MEAT or TASTE will returnvou to the DresetTable A or B.
Setting temperature rangesof Table B (if Table A USDA rangesare not suitable)
Press and hold MEAT for 2 seconds to change fiom table A to table B. Press and hold TASTE fbr 2 seconds. BEEF will be shown and the box around W.DONE and table B icon will blink. PressMEAT again to selectmeat you want to changethe temperaturefor. PressA or V to raise or lower temperature. The range can only be raised by 10 'F or lowered by 20 'F. All taste levels for meat selected will be changed by this same amount. The temperature is set when W. DONE and B stop blinking or you press TASTE. Pressand hold MEAT for 2 secondsto go back to table A.
Setting the Clock
Pressand hold SET on the rear of the receiverfor 2 seconds.12Hr will blink. PressHRS or MINS to switch from 12 hour clock to 24 hour clock. PressSET again 12:00 nu will blink. Press HRS to increasehours and MINS to increaseminutcs. Pressand hold HRS or MINS for faster settins. Press SET to set the clock.
Using the Timer
Count down
PressTl/T2 to changefrom clock to timerl or timer2. PressHRS to increasehours and MINS to increaseminutes. Pressand hold HRS or MINS for faster setting. Press
