UNPACKING
SET UP INSTRUCTIONS
Handle Bar Assembly -- Illustration 2
Do not attempt to lift the tiller from the carton. After opening the top, cut all four corners and lay the sides flat on the floor or working space. Take out all unassembled parts, bag of parts, and pro- tective packing. Be careful not to kink the control cables.
DEFINITION OF DIRECTIONS
As used throughout this manual, the following definitions apply: “Right” and “Left” refer to the operator’s right and left when standing behind the machine in the normal operating position. “For- ward” and “Rearward” likewise to directions from the viewpoint of the operator.
ASSEMBLY OF HANDLE BARS (Figures 2 & 3)
1. Attach the lower end of the handle bars to the |
rear of the chassis using four bolts, lock wash- |
ers, and nuts supplied. Assemble nuts but do not |
tighten. Note that the lower belt cover bracket |
goes under the chassis on the left rear handle |
bar bolt. |
2. Assemble the handle bar support brackets to |
Figure 2
Ref. | Part | Qty | Description |
|
|
|
|
1 | 162007 | 1 | Throttle Control Assembly |
|
|
|
|
2 | 336677 | 1 | Support LH |
|
|
|
|
3 | 336676 | 1 | Support RH |
|
|
|
|
4 | 130698 | 1 | RH Handle Assembly |
|
|
|
|
5 | 313786 | 2 | Grip |
|
|
|
|
6 | 130699 | 1 | LH Handle Assembly |
|
|
|
|
7 | 130731 | 1 | Handle Cross Brace |
|
|
|
|
8 | 400186 | 2 | Screw 5/16 - 18 x 1” Hex |
|
|
|
|
9 | 446136 | 4 | Lockwasher 5/16 Heavy |
|
|
|
|
10 | 443106 | 4 | Nut, 5/16 - 18 Hex |
|
|
|
|
11 | 402014 | 2 | #10 x 3/8” Slot Tapping Scr. |
14 | 162029 | 1 | Cable and Chain Assembly |
|
|
|
|
15 | 359346 | 1 | Clutch Locking Pin |
|
|
|
|
16 | 359359 | 1 | Spring |
|
|
|
|
17 | 359327 | 1 | Spring |
|
|
|
|
18 | 359326 | 1 | Clip |
|
|
|
|
19 | 359345 | 1 | Pin |
|
|
|
|
20 | 336683 | 1 | Lever |
|
|
|
|
21 | 400208 | 2 | 5/16 x 18 x 1 3/4 Hex Cap |
the transmission. Note the location of the clutch | |
cable guide. Assemble nuts but do not tighten. | |
3. | Assemble the Handle Panel to the handle bars |
and supports. Note the location of the clutch | |
cable guide. | |
4. | Tighten all bolts and nuts. |
5. | Assemble the throttle control to the underside |
of the panel. Secure the cable to the left handle | |
bar with the clip supplied. | |
6. | Assemble the clutch spring to the clutch le- |
ver on the handle bar. Crimp lightly so it cannot | |
come off. | |
7. | Route the loop in the end of the clutch cable |
down through the two cable guides and attach it | |
level on the idler arm weldment. Attach the chain | |
on the other end to the spring on the clutch lever. | |
Select a loop that will stretch the spring slightly | |
when the clutch lever is pulled against the handle | |
bar. | |
8. | With the throttle control in the “OFF” position |
and the clutch lever released, pull the engine | |
starter rope several times to be sure that the tines | |
do not turn. | |
Figure 3
IMPORTANT
ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL. DO NOT START ENGINE WITHOUT ADDING OIL.
Hitch Assembly
Illustration 2
Ref | Part | Qty | Description |
|
|
|
|
1 | 130670 | 1 | Rear Support Assembly |
|
|
|
|
3 | 400265 | 1 | Screw, 3/8” - 16 x 1 1/2 |
|
|
|
|
8 | 162034 | 1 | Wheel Yoke Assembly |
|
|
|
|
13 | 162031 | 2 | Wheel |
|
|
|
|
14 | 359330 | 2 | Bolt, Wheel |
|
|
|
|
16 | 444721 | 3 | 3/8” Center Locknut |
|
|
|
|
18 | 460312 | 2 | Hairpin |
|
|
|
|
19 | 461466 | 2 | Pin, 3/8” x 2 1/8” Clevis |
|
|
|
|
21 | 336685 | 1 | Drag Stake |
4
9
