Manuals / Brands / Computer Equipment / Modem / Maxon Telecom / Computer Equipment / Modem

Maxon Telecom MM-6280IND 1.32.8. 3G Quality of Service Profile (Negotiated) +CGEQNEG

1 60

Download 60 pages, 435.94 Kb

HSDPA Standard At Commands Page 51 of 60 Version 1.2

Other values are reserved.

<Maximum SDU size>: a numeric parameter (1,2,3,…) that

indicates the maximum allowed SDU size in octets (refer TS

24.008 [8] subclause 10.5.6.5).

<SDU error ratio>: a string parameter that indicates the

target value for the fraction of SDUs lost or detected as

erroneous. SDU error ratio is defined only for conforming

traffic. The value is specified as 'mEe'. As an example a target

SDU error ratio of 5•10-3 would be specified as '5E3' (e.g.

AT+CGEQMIN=…,”5E3”,…) (refer TS 24.008 [8] subclause

10.5.6.5).

<Residual bit error ratio>: a string parameter that

indicates the target value for the undetected bit error ratio in the

delivered SDUs. If no error detection is requested, Residual bit

error ratio indicates the bit error ratio in the delivered SDUs.

The value is specified as 'mEe'. As an example a target residual

bit error ratio of 5•10-3 would be specified as '5E3' (e.g.

AT+CGEQMIN=…,”5E3”,…) (refer TS 24.008 [8] subclause

10.5.6.5).

<Delivery of erroneous SDUs>: a numeric parameter

that indicates whether SDUs detected as erroneous shall be

delivered or not.

0 - no

1 - yes

2 - no detect

Other values are reserved.

<Transfer delay>: a numeric parameter (0,1,2,…) that

indicates the targeted time between request to transfer an SDU

at one SAP to its delivery at the other SAP, in milliseconds

(refer TS 24.008 [8] subclause 10.5.6.5).

<Traffic handling priority>: a numeric parameter

(1,2,3,…) that specifies the relative importance for handling of

all SDUs belonging to the UMTS bearer compared to the SDUs

of other bearers (refer TS 24.008 [8] subclause 10.5.6.5).

<PDP_type>: (see +CGDCONT and +CGDSCONT

commands).

If a value is omitted for a particular class then the value is

considered to be unspecified.

1.32.8. 3G Quality of Service Profile (Negotiated) +CGEQNEG

This command allows the TE to retrieve the negotiated QoS profiles returned in the Activate

PDP Context Accept message.

The execution command returns the negotiated QoS profile for the specified context

identifiers, <cid>s. The QoS profile consists of a number of parameters, each of which may

have a separate value.

Contents

Main HSDPA Standard AT Commands Manual Document Description REVISION HISTORY CONTACT INFORMATION TABLE OF CONTENTS Page Introduction 1.1. General 1.2. Terms 1.3. References Page Page AT INTERFACE DESCRIPTION 1.4. Basic Integration 1.7. Message Naming Convention 1.5. Serial Interface 1.6. Command Format 1.8. DTE-TA/DCE interface commands Page Page Mobile Termination errors commands 1.9. Report Mobile Termination error( +CMEE) 1.9.1. Mobile Termination error result code (CME ERROR) Page 1.10. Informative examples General commands 1.11. Request manufacturer identification(+CGMI) 1.12. Request model identification(+CGMM ) 1.13. Request product serial number identification (+CGSN) 1.14. Select TE character set (+CSCS) 1.15. ITU-T V.250 generic TA control commands 1.16. PCCA STD101 [17] select wireless network +WS46 1.17. Informative examples 1.17.1. Phone model 1.17.2. Phone Manufacturer 1.17.3. Checking mobile state 1.17.6. Supported alphabets 1.17.7. Supported alphabets Network service commands 1.18. Subscriber number +CNUM 1.19. Network registration +CREG HSDPA Standard At Commands Page 25 of 60 Version 1.2 Table 15. +CREG parameter command syntax 1.20. PLMN selection +COPS HSDPA Standard At Commands Page 26 of 60 Version 1.2 Table 16. +CREG parameter command syntax 1.21. Facility lock +CLCK Page 1.22. Change password +CPWD 1.23. Preferred PLMN list +CPOL 1.24. Read operator names +COPN 1.25. Informative examples 1.25.1. Operator information reading 1.25.2. IMSI number reading 1.25.3. GPRS Attachment 1.25.4. Network registration 1.25.5. Own number reading Mobile Termination control and status commands 1.26. Basic TE 1.27. Signal quality +CSQ 1.28. Clock +CCLK 1.29. Band Selection (AT$$MBAND) 1.30. Enter PIN +CPIN 1.31. Informative examples 1.31.1. Signal strength reading 1.31.2. Pin registration Packet Domain Command(GPRS) 1.32. UMTS packet Domain commands 1.32.1. Define PDP Context +CGDCONT 1.32.2. Define Secondary PDP Context +CGDSCONT HSDPA Standard At Commands Page 40 of 60 Version 1.2 Table 29. +CGDCONT parameter command syntax 1.32.3. Traffic Flow Template +CGTFT HSDPA Standard At Commands Page 41 of 60 Version 1.2 Table 30. + CGTFT parameter command syntax Page HSDPA Standard At Commands Page 43 of 60 Version 1.2 1.32.4. Quality of Service Profile (Requested) +CGQREQ Table 31. + CGQREQ parameter command syntax HSDPA Standard At Commands Page 44 of 60 Version 1.2 1.32.5. Quality of Service Profile (Minimum acceptable) +CGQMIN Table 32. + CGQMIN parameter command syntax HSDPA Standard At Commands Page 45 of 60 Version 1.2 1.32.6. 3G Quality of Service Profile (Requested) +CGEQREQ Table 33. + CGEQREQ parameter command syntax Page Page 1.32.7. 3G Quality of Service Profile (Minimum acceptable) +CGEQMIN Page Page 1.32.8. 3G Quality of Service Profile (Negotiated) +CGEQNEG Page 1.32.9. PS attach or detach +CGATT 1.32.10. PDP context activate or deactivate +CGACT 1.32.11. PDP Context Modify +CGCMOD 1.32.12. Enter data state +CGDATA 1.32.13. Show PDP address +CGPADDR 1.33. Modem compatibility commands 1.34. Informative examples 1.34.1. UMTS Connection Synchronous data mode commands Qualcomm commands