Manuals / Maxtor / Computer Equipment / Computer Drive

Maxtor 2160, 86480D6, 88400D8, 84320D4 Unpacking and Inspection, Multi-pack Shipping Container

Models: 82160D2 84320D4 2160 83240D3 86480D6 88400D8

1 63

Download 63 pages 27.7 Kb

Page 23

Image 23

INSTALLATION

Unpacking and Inspection

Retain any packing material for reuse. Inspect the shipping container for evidence of damage in transit. Notify the carrier immediately in case of damage to the shipping container.

As they are removed, inspect drives for evidence of shipping damage or loose hardware. If a drive is damaged (and no container damage is evident), notify Maxtor immediately for drive disposition.

Figure 4 - 1

Multi-pack Shipping Container

4 – 2

Page 23

Image 23

Maxtor 86480D6, 88400D8, 84320D4, 83240D3, 82160D2 specifications Unpacking and Inspection, Multi-pack Shipping Container

Contents

DiamondMax REV EC no Section Description Date U T I O N Before You BeginContents AT Interface Description Product SpecificationsHandling and Installation Host Software Interface Glossary Interface CommandsService and Support Figures Abbreviations IntroductionMaxtor Corporation Manual OrganizationNumbering Signal ConventionsConventions Key WordsProduct Description DiamondMax 2160 Key FeaturesFunctional / Interface Product FeaturesSoftware ECC Correction On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Defect Management Zone DMZAutomatic Write Reallocation AWR Read-Ahead ModeCache Management Buffer SegmentationMajor HDA Components Dual Drive Support Subsystem ConfigurationJumper Location/Configuration Cylinder LimitationModels and Capacities Product SpecificationsDrive Configuration Performance SpecificationsParameter Standard Metric Physical DimensionsOutline and Mounting Dimensions Environmental Limits Power Requirements AveragePower Mode Definitions EPA Energy Star ComplianceShock and Vibration Reliability SpecificationsStandard Test Methods Safety Regulatory ComplianceImportant Notice Handling and InstallationHard Drive Handling Precautions Pre-formatted DriveMulti-pack Shipping Container Unpacking and InspectionRepacking Physical InstallationRecommended Mounting Configuration Master Device Slave Device Drive Jumper SettingsInstalling 5.25-inch Mounting Brackets Mounting Drive in SystemMounting Drive in 3.5-inch Bay Inch InstallationMounting Drive in 5.25-inch Bay IDE Interface and Power Cabling Detail Attaching IDE Interface and Power CablesSystem Mother board Cabling Attaching System CablesSystem Interface Card Cabling Set the Bios Cmos parameters as follows System SetupSetting the Bios Cmos Model CYL SPT System Hangs During BootSystem/Drive Information Hard Drive PreparationPin Description Summary Interface ConnectorData Connector AT Interface DescriptionPin Description Table PIN Name Signal Name Signal DescriptionPIO Data Transfer To/From Device PIO TimingMulti-word DMA Data Transfer DMA TimingInitiating an Ultra DMA Data In Burst Ultra DMA TimingSustained Ultra DMA Data In Burst Host Pausing an Ultra DMA Data In BurstHost Terminating an Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In BurstSustained Ultra DMA Data Out Burst Initiating an Ultra DMA Data Out BurstHost Terminating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out BurstDevice Terminating an Ultra DMA Data Out Burst Task File Registers Error RegisterFeatures Register Host Software InterfaceDevice/Head Register Sector Count RegisterSector Number Register Cylinder Number RegistersCommand Register SDH Command Name Command Code Parameters UsedTimer Value TIME-OUT Period SummaryDigital Input Register Control Diagnostic RegistersAlternate Status Register Device Control RegisterInterrupt Handling Reset and Interrupt HandlingReset Handling Set Feature Commands Interface CommandsRead Verify Sectors Read CommandsRead Sectors Read Multiple Read DMAWrite Verify Sectors Write CommandsSet Multiple Mode Write SectorsWrite DMA Write MultipleValue Description Set Feature CommandsSet Features Mode Power Mode Commands Timer Value TIME-OUT Period Identify Drive Initialization CommandsWord Content Description Word Content Description = Write Cache enabled Initialize Drive Parameters Format Track Seek, Format and Diagnostic CommandsExecute Drive Diagnostic Error Code DescriptionExecute S.M.A.R.T A.R.T. Command SetSupport Service and SupportService Policy No Quibble ServiceInternet MaxFax ServiceBulletin Board Service Customer Service