Maytag MMV5208WS installation instructions Attach Mounting Plate to Wall, Prepare Upper Cabinet

Installation for Wall Stud at One End Hole (Figure 3)

1.Drill a 3/16" (5 mm) hole into the wall stud at the end hole marked in Step 3 of “Mark Rear Wall.”

2.If installing on a second wall stud, drill a 3/16" (5 mm) hole into the wall stud at the other hole marked in Step 6 of “Mark Rear Wall.” Refer to Figure 3 in “Possible Wall Stud Configurations” in “Locate Wall Stud(s)” section.

3.Drill a 3/4" (19 mm) hole through the wall at the other end hole.

Installation for Wall Studs at Both End Holes (Figure 4)

Drill 3/16" (5 mm) holes into the studs at the end holes marked in Step 3 of “Mark Rear Wall.”

Attach Mounting Plate to Wall

NOTE: Secure the mounting plate to the wall at both end holes drilled into the wall studs and/or drywall using either 1/4-20 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag screws.

Refer to illustrations in “Possible Wall Stud Configurations” in “Locate Wall Stud(s)” section.

No Wall Studs at End Holes (Figures 1 & 2)

NOTE: The mounting plate must be secured to the wall on at least 1 wall stud as well as at both ends.

1.With the support tabs of the mounting plate facing forward, insert 1/4-20 x 3" round-head bolts through both end holes of mounting plate.

2.Start toggle nuts on bolts from the back of the mounting plate. Leave enough space for the toggle nuts to go through the wall and to open.

B

A

C

A. 1/4-20 x 3" round-head bolt

B. Mounting plate

C. Spring toggle nut

3.Position mounting plate on the wall.

4.Push the 2 bolts with toggle nuts through the drywall, and finger tighten the bolts to make sure toggle nuts have opened against drywall.

C

A

B

D

A. 1/4-20 x 3" round-head bolt

B. Mounting plate

C. Spring toggle nut

D. Drywall

5.Insert lag screw(s) into the hole(s) drilled into wall stud(s) in Step 2 of “Installation for No Wall Studs at End Holes” in the “Drill Holes in Rear Wall” section.

6.Check alignment of mounting plate, making sure it is level.

7.Securely tighten all lag screws and bolts.

Wall Stud at One End Hole (Figure 3)

1.With the support tabs of the mounting plate facing forward, insert a 1/4-20 x 3" round-head bolt through the end hole that fits over the 3/4" (19 mm) hole drilled in Step 3 of “Installation for Wall Stud at One End Hole” in the “Drill Holes in Rear Wall” section.

2.Start a toggle nut on the bolt from the back of the mounting plate. Leave enough space for the toggle nut to go through the wall and to open.

3.Position mounting plate on the wall.

4.Push the bolt with toggle nut through the drywall, and finger tighten the bolt to make sure toggle nut has opened against drywall.

5.Insert a lag screw into the remaining end hole.

6.If installing on a second wall stud, insert a lag screw into the other hole drilled in Step 2 of “Installation for Wall Stud at One End Hole” in the “Drill Holes in Rear Wall” section.

7.Check alignment of mounting plate, making sure it is level.

8.Securely tighten the lag screw(s) and bolt.

Wall Studs at Both End Holes (Figure 4)

1.Position mounting plate on the wall.

2.Insert lag screws into both end holes.

3.Check alignment of mounting plate, making sure it is level.

4.Securely tighten the lag screws.

Prepare Upper Cabinet

1.Disconnect power to outlet.

2.Remove all contents from upper cabinet.

3.Place Upper Cabinet Template against the bottom of the upper cabinet, and attach with tape or thumbtacks. Make sure the template centerline aligns with the vertical centerline on the rear wall.

The “rear wall” arrows must be against the rear wall so that the holes cut into the upper cabinet align with the holes in the top of the microwave oven.

NOTE: If the upper cabinet has a frame around it, trim the template edges so that it fits inside the frame, against the upper cabinet bottom. The template has trim lines to use as guides.

4.Make sure the 10" (25.4 cm) dimension from the rear wall to points “D” and “E” on the template is maintained.

Upper-cabinet template
D		E
10"	G	10"
(25.4 cm)		(25.4 cm)
	F

8