General Information, Introduction | MB QUART SCR specs

Section 1

GENERAL INFORMATION

1.1 INTRODUCTION

Your mower was built to the highest standards in the industry. However, the prolonged life and maximum efficiency of your mower depends on you following the operating, maintenance and adjustment instructions in this manual.

If additional information or service is needed, contact your Scag Power Equipment Dealer.

We encourage you to contact your dealer for repairs. All Scag dealers are informed of the latest methods to service this equipment and provide prompt and efficient service in the field or at their service shop. They carry a full line of Scag service parts.

USE OF OTHER THAN ORIGINAL SCAG REPLACEMENT PARTS WILL VOID THE WARRANTY.

When ordering parts, always give the model and serial number of your tractor. The serial number plate is located where shown in Figure 1-1.

For pictorial clarity, some illustrations and figures in this manual may show shields, guards or plates open or removed. Under no circumstances should your mower be operated without these devices in place.

All information is based upon product information available at the time of approval for printing. Scag Power Equipment reserves the right to make changes at any time without notice and without incurring any obligation.

1.2 DIRECTION REFERENCE

The “Right” and “Left”, “Front” and “Rear” of the machine are referenced from the operator’s right and left when seated in the normal operating position and facing the forward travel direction.

1.3SERVICING THE ENGINE AND DRIVE TRAIN COMPONENTS

The detail servicing and repair of the engine, hydraulic pumps and gearboxes are not covered in this manual; only routine maintenance and general service instructions are provided. For service of these components during the limited warranty period, it is important to contact your Scag dealer or find a local authorized servicing agent of the component manufacturer. Any unauthorized work done on these components during the warranty period may void your warranty.

Serial Plate

SCR 2K SPL

Figure 1-1 Tractor Serial Number Plate Location

1

Image 3

MB QUART SCR manual General Information, Introduction, Direction Reference, Servicing the Engine and Drive Train Components

Contents

OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Servicing the Engine and Drive Train Components General InformationIntroduction Direction Reference ISO Symbols CE Mark Symboldescription Safety Information Signal WordsBefore Operation Considerations Operation Considerations Maintenance Considerations Read Operators Manual Tractor SpecificationsEngine Electrical Grass Catching System Weights and DimensionsTractor Contd Cutter Deck Controls and Instrument Identification Operating Instructions Dump Valves Location Safety Interlock System Ground Travel and Steering Starting the Engine Reverse Travel Forward Travel Hillside Operation Engaging the Deck Drive Cutter Blades HOPPER, Mulch or Side Discharge Operation Parking the MowerAfter Operation 10 Tailgate Operation Grass Catching Operation Mulching Operation Side Discharge OperationRemoving Clogged Material Adjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing 15 Deck Locking Pin Tilting the Cutter Deck Condition Cause Cure Troubleshooting Cutting Conditions Scalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause Cure Ground Troubleshooting Contd Parking Brake Adjustment Adjustments Travel Adjustments Neutral Adjustment Drive linkage Tracking Adjustment Belt Alignment Cutter Deck Engagement Belt AdjustmentThrottle Control and Choke Adjustment Belt Adjustment Cutter Deck Adjustments Maintenance Chart Recommended Service Intervals Maintenance Lubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals Contd Right Side Under Seat Checking Hydraulic Oil Level Checking Engine Crankcase Oil LevelChanging Hydraulic Oil Filling the Fuel Tank Changing Engine Crankcase OilChanging Engine Oil Filter Engine Fuel System Cleaning and/or Replacing Air Cleaner Element BatteryChecking Electrolyte Level and Cleaning Battery Engine AIR Cleaner Jump Starting Charging the Battery Cutter Blades Blade ReplacementDrive Belts Blade Sharpening Checking Lubricant Level TiresHopper Cutter Deck Gearbox 10 Gearbox Drain Plug Power Unit Gearbox 13 Fluid Level BODY, DECK, Hopper and UpholsteryPage Cutter Decks Number Description Cutter Decks Cutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Part Engine Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Kohler Electrical System Part Number Description Kawasaki Electrical System Kawasaki Electrical System Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Cutting Height Replacement Decals and Information Plates SCR 2K RD2 Kohler Electrical Schematic Limited Warranty Commercial Equipment 2002 Kawasaki Electrical Schematic