Adjustments, Parking Brake Adjustment | MB QUART SCR manual

Section 6

R

ADJUSTMENTS

6.1 PARKING BRAKE ADJUSTMENT

WARNING:

Do not operate the mower if the parking brake is not operable. Possible severe injury could result.

The parking brake linkage should be adjusted whenever the parking brake lever is placed in the “ENGAGE” position and the parking brake will not prevent the mower from moving. If the following procedures do not allow you to engage the parking brake properly, contact your Scag dealer for further brake adjustments.

1.Position a floor jack under the left side of the machine behind the drive wheel. Raise the machine and support it to prevent it from falling. Block the caster wheels to prevent the machine from moving. Remove the right drive wheel and reinstall (2) lug nuts to hold the hub on.

2.With the brake lever in the engaged position, check to see if the lever plunges the brake switch within 1/8" of bottoming out. (See Figure 6-1). To increase the distance, loosen the jam nuts on the parking brake control rod and turn the rod clockwise. To decrease the distance, turn the rod counterclockwise. (See Figure 6-2).

Brake

Switch

1/8"

SCR 2K BSA

Park Brake Control

Park Brake Control Rod

SCR 2K BLA2

Figure 6-2 Brake Switch Adjustment

3.With the brake in the engaged position, check the distance between the lower nut on the brake actuator rod and the spring housing. The distance should be approximately 1/16". (See Figure 6-3).

4.Turn the nut at the top of the brake connector link until the 1/16" measurement is achieved and tighten the jam nut at the connector link on the brake actuator rod. (See Figure 6-3).

5.Repeat steps 3 and 4 on other side. Replace the drive wheels and test the brake.

-NOTE-

If this procedure does not achieve proper brake adjustment, please contact your authorized Scag dealer for diagnosis and repair.

Figure 6-1 Brake Switch

23

Image 25

MB QUART SCR manual Adjustments, Parking Brake Adjustment

Contents

OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Introduction General InformationDirection Reference Servicing the Engine and Drive Train Components ISO Symbols CE Mark Symboldescription Signal Words Safety InformationBefore Operation Considerations Operation Considerations Maintenance Considerations Read Operators Manual Engine SpecificationsElectrical Tractor Tractor Contd Weights and DimensionsCutter Deck Grass Catching System Controls and Instrument Identification Operating Instructions Dump Valves Location Safety Interlock System Ground Travel and Steering Starting the Engine Reverse Travel Forward Travel Hillside Operation Engaging the Deck Drive Cutter Blades Parking the Mower HOPPER, Mulch or Side Discharge OperationAfter Operation 10 Tailgate Operation Grass Catching Operation Side Discharge Operation Mulching OperationRemoving Clogged Material Moving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing 15 Deck Locking Pin Tilting the Cutter Deck Condition Cause Cure Troubleshooting Cutting Conditions Scalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause Cure Ground Troubleshooting Contd Parking Brake Adjustment Adjustments Travel Adjustments Neutral Adjustment Drive linkage Tracking Adjustment Throttle Control and Choke Adjustment Cutter Deck Engagement Belt AdjustmentBelt Adjustment Belt Alignment Cutter Deck Adjustments Maintenance Chart Recommended Service Intervals Maintenance Lubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals Contd Right Side Under Seat Checking Engine Crankcase Oil Level Checking Hydraulic Oil LevelChanging Hydraulic Oil Changing Engine Oil Filter Changing Engine Crankcase OilEngine Fuel System Filling the Fuel Tank Checking Electrolyte Level and Cleaning Battery BatteryEngine AIR Cleaner Cleaning and/or Replacing Air Cleaner Element Jump Starting Charging the Battery Drive Belts Blade ReplacementBlade Sharpening Cutter Blades Hopper TiresCutter Deck Gearbox Checking Lubricant Level 10 Gearbox Drain Plug Power Unit Gearbox 13 Fluid Level BODY, DECK, Hopper and UpholsteryPage Cutter Decks Number Description Cutter Decks Cutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Part Engine Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Kohler Electrical System Part Number Description Kawasaki Electrical System Kawasaki Electrical System Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Cutting Height Replacement Decals and Information Plates SCR 2K RD2 Kohler Electrical Schematic Limited Warranty Commercial Equipment 2002 Kawasaki Electrical Schematic