Meade instruction manual LXD75-SeriesYour Personal Window to the Universe

Caution: Using products other than standard Meade accessories may cause damage to the telescope’s internal electronics and may void the Meade warranty.

d Want to learn more about the eyepieces available for your

LXD75-Series

telescope?

See OPTIONAL

ACCESSORIES, page

37.

e Want to learn more about aligning the viewfinder? See page 14.

h Want to learn more about attaching the viewfinder? See page 12.

1! Want to learn more about assembling your telescope?

See ASSEMBLING YOUR TELESCOPE, page 11.

1@ EC Handbox users,

see Appendix D, page 62, for more informa- tion.

LXD75-Series:Your Personal Window to the Universe

The Meade LXD75-Series models are versatile, high-resolution telescopes. Supplied with either an Electronic Controller or an Autostar handbox, the LXD75-Series models offer unmatched mechanical and electronic performance.

The LXD75-Series telescopes reveal nature in an ever-expanding level of detail. Observe the feather structure of an eagle from 50 yards or study the rings of the plan- et Saturn from a distance of 800 million miles. Focus beyond the Solar System and observe majestic nebulae, ancient star clusters, and remote galaxies. Meade LXD75- Series telescopes are instruments fully capable of growing with your interest and can meet the requirements of the most demanding advanced observer.

Refer to Figures 1a through 1e for the following features:

B Eyepiece Thumbscrew: Tightens the eyepiece (see d) in place. Tighten to a firm feel only.

C Eyepiece Holder: Holds eyepiece in place. Holders supplied for both 1.25" and 2" eyepieces.

Diagonal (not shown, achromatic refractor and Schmidt-Cassegrain models

only): Provides a more comfortable right-angle viewing position. Slide the diagonal directly into the eyepiece holder (see c) and tighten the thumbscrew on the eye- piece holder to a firm feel only. See page 13 for a photo and more information.

D Eyepiece: Place the supplied Super Plössl 26mm eyepiece into the eyepiece holder or the diagonal and tighten in place with the eyepiece thumbscrew (see b). The eyepiece magnifies the image collected in the optical tube.

D8 x 50mm (all models, except N-6EC Newtonian) or 6 x 30mm (N-6EC Newtonian only) Viewfinder: A low-power,wide-field sighting scope with

crosshairs that enables easy centering of objects in the telescope eyepiece (see d).

EViewfinder Collimation Screws (6): Use these screws to adjust the alignment of the viewfinder.

FViewfinder Front Cell and Locking Ring: Adjust the front cell to focus the viewfinder. See step 3, page 14 for more details. The viewfinder is supplied with a small dust cover placed over the front cell.

GViewfinder Bracket: Holds the viewfinder in place.

HFocus Knobs: Moves the telescope’s focuser drawtube in a finely-controlled motion to achieve precise image focus. The LXD75-Seriestelescopes can be focused on objects from a distance of about 75 ft. to infinity. Rotate the focus knobs to focus on objects.

ICorrector/Dust Cover: Place the dust cover (not visible in photo) over the cor- rector when storing the telescope.

Note: The dust cover should be replaced after each observing session and the power turned off to the telescope. Allow time for any dew that might have collected during the observing session to evaporate prior to replacing the dust cover.

1) Optical Tube: The main optical component that gathers the light from distant objects and brings this light to a focus for examination through the eyepiece.

1! Cradle Assembly: Attaches to mount base. See 1# and 1$.

1@ Autostar™: See pages 9 and 10 for a description of features.

1# Cradle Ring Lock Knobs (2) and Washers (2): Slide washers onto lock knobs before inserting. Tighten to a firm feel to secure the optical tube in place.

1$ Cradle Rings (2): Part of the cradle assembly (see 1!); hold the optical tube firm- ly in place.

6