Meade instruction manual Simple Observations, Initializing the Control Panel NGC Models Only

NOTE: If you have some familiarity with “Go To” telescopes, you might be wonder- ing why you you weren’t asked to enter the time and date, the two most important factors in a Go To system.

The reason is that your telescope contains a high-precision internal clock that is set at the factory. The clock has a battery that will hold the time and date information for about 5 years.

If you wish to set the time manually or change the battery, see Appendix B for more information.

NOTE: Sometimes air gets trapped below the compass dial causing the compass to not work properly.

Gently tap the compass to insure that no air is trapped below the compass dial.

Fig. 12: Remove the eye- piece and slide in the com- pass/ bubble level.

located and centered in the eyepiece, you may wish to switch to a higher power eye- piece to enlarge the image as much as practical for prevailing seeing conditions.

NOTE: Seeing conditions vary widely from night-to-night and site-to-site. Turbulence in the air, even on an apparently clear night, can distort images. If an image appears fuzzy and ill-defined, back off to a lower power eyepiece for a more well-resolved image (Figs. 11a and 11b).

The power, or magnification of a telescope is determined by the focal length of the tel- escope and the focal length of the eyepiece being used. To calculate eyepiece power, divide the telescope's focal length by the eyepiece's focal length. E.g., a 25mm eye- piece is used with a NGC60 telescope. The focal length of the NGC60 is 700mm (see SPECIFICATIONS, page 21).

Focal length ÷ Eyepiece focal length = Power

700mm ÷ 25mm = 28

The eyepiece power, or magnification is therefore 28x.

Simple Observations

If you wish to observe a distant land object, such as a mountain top, you can observe by merely pointing the telescope and looking through the eyepiece.

•Move your telescope to observe distant street signs, mountains, trees and other structures. Use your viewfinder to help site-in on an object.

•Practice focusing objects with the focus knob (10, Fig. 1).

•Once you get a feel for how your telescope moves and focuses, try to view some- thing more challenging, like a bird or a distant moving train.

You can also observe stars and objects in the night sky using this method, but note that objects begin to slowly drift across the eyepiece field. This motion is caused by the rotation of the Earth. You'll find that you will need to reposition your telescope from time to time to keep an object in the eyepiece field of view. This is especially true when using high-power eyepieces.

Viewing terrestrial objects requires looking along the Earth's surface through heat waves. These heat waves often cause loss of image quality. Lower power eyepieces, such as 25mm or 26mm eyepieces, magnify these heat waves less than higher power eyepieces. Therefore, lower power eyepieces provide a steadier, higher quality image. If the image is fuzzy or ill-defined, reduce to a lower power eyepiece, where the heat waves do not have such an effect on image quality. Observing in early morning hours, before the ground has built up internal heat, produces better viewing conditions than during late afternoon hours.

If you have an NGC model telescope, you can locate stars and other celestial objects (over 1400 objects in all) using the control panel. In order to do so, you must initialize the control panel, set the telescope in the home position, and align the telescope. The control panel uses this information to determine the location of celestial objects.

Initializing the Control Panel (NGC Models Only)

1.Make sure that you have installed a 9v battery in the battery compartment.

2.Press ON/OFF to turn the power on.

The control panel display lights up and a copyright message displays briefly.

3.The next screen requests the status of Daylight Savings Time. Use UP/DOWN to move between the "Yes" and "No" settings. Select the desired setting by pressing

ENTER.

NOTE: Daylight Savings Time may be referred to by a different name in various areas of the world.

NOTE: When multiple choices are available within a menu option, the cur- rent option is usually displayed first and highlighted by a right pointing arrow (>).

3.The Location screen displays. This screen asks you if you wish to choose either the zip code of your observing location or the location (i.e.,entering the city and state or country of your observing location). Press Up to the zip code option or down to enter the city and state.

10