Meade LXD 75 Getting Started, How to Assemble Your Telescope, Telescope Assembly, Accessories

Bushing	Second
	slot

Fig. 5a: Slide bushing over shaft.

Second slot

E-clip

Fig. 5b: Snap e-clip all the way onto shaft above mount (shown partially attached).

Fine
Azimuth
Control
Knobs	Place mount over
	shaft with bushing
Protrusion	and c-clip.

Fig. 5c: Attach the mount to the tripod.

Dec. Setting Circle

Shaft

Base

Counterweight

Lock

Knob

Shaft

Safety

Cap

Fig. 6: Attach counterweight assembly.

GETTING STARTED

As you unpack your telescope, carefully note the following parts. The assembly is shipped in separate boxes.

Telescope Assembly

■Equatorial mount with polar alignment finder

■Heavy duty, adjustable aluminum tripod with leg braces, three tripod leg lock knobs, and a captive mount locking knob

■Complete optical tube assembly including primary mirror with dust cover and a rack-and-pinion focuser and eyepiece holders for both 1.25" and 2" eyepiece holders, tube cradle assembly with two rings and two lock knobs

■Super Plössl (SP) 26mm eyepiece

■Counterweight and counterweight shaft. The 8" and 10" models include extra counterweights.

■8 x 50mm (all models, except N-6EC Newtonian) or 6 x 30mm (N-6EC Newtonian only) viewfinder.

■Factory-mounted dual electronic motor drive assembly

■Autostar handbox, detachable coil cord, or Electronic Controller

■Battery pack and holder

Accessories

■Hex keys, T-Adapter (included with Schmidt-Newtonian models only)

How to Assemble Your Telescope

The giftboxes contain the optical tube assembly and the tripod with the equatorial mount. The accessories are located within compartments custom-cut into the styro- foam block inserts.

1.Remove the components from the giftboxes: Remove and identify the tele- scope’s equipment. Refer to Figures 1a through 1f for images of the parts and the overall assembly of your telescope. When removing the tripod from the gift- box, hold the assembly parallel (horizontal) to the ground or the inner tripod leg extensions will slide out as they are not locked in place.

2.Adjust the tripod legs. Spread the tripod legs as far as they will open. See Fig. 3.

3.Attach the spreader bar to the tripod with shaft: Thread the tension knob onto the shaft (see Fig. 4). Place the spreader bar over the T-handle shaft. Slide the bushing, the wide open side facing downward, onto the shaft as far as it will go (Fig. 5a). Then slide the shaft up through the tripod mounting base (37, Fig. 1c). Above the mount, snap the e-clip into the second, narrower precut slot (see Fig. 5a) of the shaft (Fig. 5b).

4.Attach mount to tripod base: Place the mount over the tripod mounting base (37, Fig. 1c) and onto the shaft, with the protrusion on top of the tripod's base positioned between the fine azimuth control knobs (27, Fig. 1d). See Fig. 5c. If necessary, back off the azimuth control knobs wide enough for protrusion to fit between them.

Tighten the T-handle to a firm feel. This attachment keeps the tripod and the tel- escope mount securely in place. Then line up the spreader bar braces so that they are each touching one of the tripods legs. Tighten the tension knob (39, Fig. 1c) to a firm feel. When you wish to collapse the tripod, loosen the tension knob and move the braces off the legs. You do not need to remove the T-handle/shaft.

5.Attach the counterweight(s) to the counterweight shaft: Place the counter- weight shaft base (20, Fig. 1d) over the threaded end of the shaft (22, Fig. 1d). Thread the shaft and base assembly into the hole beneath the Dec. setting circle as depicted in Fig. 6.

Look through the hole in the counterweight and note the pin blocking the hole. Tilt the counterweight slightly and the pin moves out of position, clearing the hole. If the pin does not move, unscrew the counterweight lock knob slightly until the pin moves.

Unscrew the safety cap (23, Fig. 1d) from the shaft. Holding the counterweight (21, Fig. 1d) firmly in one hand, slip the counterweight to approximately the mid- point of the counterweight shaft (22, Fig. 1d). Tighten the counterweight lock

11