•Mount heating head on curved bar so that hole in bar is aligned with hole in heating head. Secure using mounting screw.
•Check that the appliance is firmly fixed in place before using it.
Models with stand (model 670-207/209/211)
•The appliance should be sited at least 1m from the nearest wall. The heater head should be at least 30cm from the ceiling, and at least 1.8m above the floor. The appliance should stand firmly on a horizontal floor.
•Fit lower part of stand (b) in base (a), lay base on its side, and fasten stand to underside of base with washer and screw (c) (See illus. I).
•Position base correctly so that stand is upright. Slacken screw (c) in middle of stand (d), and insert middle part into lower part. Align screw with recess in lower part
(see illus. II). Tighten screw. In the same way, fix upper part of stand (e) in middle part with a screw (see illus. III).
•Extend thin rod (f) from sleeve (g) at top of rod to desired height. Fit cuff (h) over thin rod. Tighten cuff (see illus. IV).
•Mount heating head on thin rod so that hole in the rod is aligned with hole in heating head. Secure using mounting screw (14) (see illus. V). Tighten all screws thoroughly.
•Check that the appliance is standing firmly in place before using it.
•The cable may be secured in the cable holder (j) on the stand.
•The curved stand can be rotated 360° so that the heating head can face in any direction.
OPERATING THE APPLIANCE
•If the appliance has a stand, angle and height of heating head can be adjusted.
o Set head at desired angle by turning the hinge (12).
o Set head at required height by slackening the cuff and extending or retracting the thin rod.
•The appliance is not thermostatically controlled and continues to emit heat until it is switched off. Always keep an eye on the appliance while it is switched on.
•Remove the plug from the wall socket when appliance is not in use.
Models with no remote control:
•Plug in and switch on the power.
•The appliance is switched on, setting selected and switched off by pulling the string (5). Settings can be seen in function indicator (4): The appliance will switch to next setting each time the string is pulled (see list below).
•Switch appliance off when you have finished using it. Pull string repeatedly until indicator shows "0".
Models with remote control:
•Plug in and switch on the power. The green diode will flash to indicate the appliance is on standby.
•Press On/Power (8) once on the appliance or remote control to switch on at lowest setting. Switch between low, medium and high using this button. Settings can be seen in the function indicator (7) (see list below).
•Press Off (10) on appliance or remote control to return to standby. Caution! The appliance will not be completely switched off using the Off button, but will go into standby mode (green diode will flash). Disconnect power and check all diodes are out when finished with the appliance.
•Always point remote control at receiver (9) on heating head when using.
| Indicator (no | Indicator (with | Meaning | Power |
| remote control) | remote control) |
| | |
| | | | |
| 0 | Green diode flashing | Off/standby | 0 W |
| | | | |
| L | Green diode lit | Low power | 650 W |
| | | | |
| M | Yellow diode lit | Medium power | 1,350 W |
| | | | |
| H | Red diode lit | High power | 2,000 W |
| | | | |
Quartz tubes
The quartz tubes in the appliance (3) emit long wave infrared radiation. They have a service life of approx. 5,000 hours and must be replaced by an electrician when burnt out. Quartz tubes are fragile, and must not be touched directly and protected from impact or shock.
Two dark spots can appear on the tubes within the first few minutes of use. This is normal, and they will disappear after a little while.
CLEANING
•Always switch off at wall socket and unplug before cleaning the appliance.
•Clean the outside of the appliance by wiping with a damp cloth. A little detergent can be added if the appliance is heavily soiled.
•Never use a scouring pad, steel wool or any form of strong solvents or abrasive cleaning agents to clean the appliance, as those may damage the outside surfaces of the appliance.
•After extended periods of use dust can collect on the reflector and tubes behind the grille (2). Contact a professional for removing the grille and cleaning the head inside.
INFORMATION ON DISPOSAL AND RECYCLING OF THIS PRODUCT
Please note that this Adexi product is marked with this symbol: 
This means that this product must not be disposed of together with ordinary household waste, as electrical and electronic waste must be disposed of separately.
In accordance with the WEEE directive, every member state must ensure correct collection, recovery, handling and recycling of electrical and electronic waste. Private households in the EU can take used equipment to special recycling stations free of charge. In certain member states, used appliance can be returned to the dealer where they were bought on the condition you buy new products. Contact your retailer, distributor or the municipal authorities for further information on what you should do with electrical and electronic waste.
GUARANTEE TERMS
The guarantee does not apply:
•if the above instructions are not followed
•if the appliance has been interfered with
•if the appliance has been mishandled, subjected to rough treatment, or has suffered any other form of damage
•if faults have arisen because of faults in your electricity supply.
Due to the constant development of our products in terms of function and design, we reserve the right to make changes to the product without prior warning.
QUESTIONS AND ANSWERS
If you have any questions regarding use of the appliance and cannot find the answer in this user guide, please try our website at www.adexi.eu.
Go to the "Consumer Service" menu, click on "Question & Answer" to see the most frequently asked questions.
You can also see contact details if you need to contact us for technical issues, repairs, accessories and spare parts.
IMPORTER
Adexi Group
www.adexi.eu
We cannot be held responsible for any printing errors.
