Melissa 670-207, 670-211 Introduction, Important Safety Precautions, Positioning the Appliance

UK

INTRODUCTION

To get the best out of your new appliance, please read this user guide carefully before using it for the first time. Take particular note of the safety precautions. We also recommend that you keep the instructions for future reference.

IMPORTANT SAFETY PRECAUTIONS

•Incorrect use of this appliance may cause personal injury and damage.

•Use for its intended purpose only. Do not use for drying towels, clothes or the like. The manufacturer is not responsible for any injury or damage resulting from incorrect use or handling (see also Guarantee Terms).

•For domestic use only. Not for commercial use. Do not use for heating building sites, greenhouses, barns or the like.

•For connection to 230 V, 50 Hz only.

•Handle with care. The quartz tubes in the heating head are fragile. Avoid subjecting to heavy impact. Do not remove the grille. If necessary to clean the heating head inside, contact a professional.

•The appliance should be set up or mounted in accordance with the instructions in section “Positioning of the appliance” below.

•The appliance is high powered and can emit very intense heat. Do not expose animals or small children to direct heat from the appliance.

•The appliance must never be mounted or used in the vicinity of flammable objects, e.g. curtains, furniture, etc. It must not be set up or mounted in wet or damp environments (in bathrooms, by swimming pools, etc.).

•Do not use the appliance outdoors in wet weather!

•In order to reduce the risk of fire or electric shock, never use the appliance together with an electronic timer or device which turns on and off the appliance automatically.

•Do not cover.

•Do not cover or block the remote control receiver (remote control models only). This will prevent the signal being received.

•Ensure that the cable does not get caught beneath the appliance, behind shelves etc. Do not run the cable under carpets, rugs, etc. Place the cable so that it is not possible to trip over it, and avoid wrapping it around the stand (only models with base) or heater head.

•If use of an extension cable is required with the appliance, then the extension cable should have a minimum rating of 10A and 2000W. If a cable reel is used, then it should be unrolled entirely.

•Do not submerge in any form of liquid.

•Never insert your fingers, pencils or other objects through the grille. The grille will become hot during use and must not be touched until the appliance has cooled down.

•Switch off and allow to cool before moving or cleaning.

•Keep an eye on any children in the vicinity of the appliance when it is in use. Children must not be allowed to use the appliance unless supervised by an adult.

•Never try to repair the appliance yourself. If the appliance, cable or plug needs to be repaired, it should be taken to an authorised service centre. Unauthorised repairs or modifications will invalidate the guarantee. Please contact the store where you bought the appliance for repairs under guarantee.

KEY TO MAIN COMPONENTS OF THE APPLIANCE

1.Heating head

2.Grille

3.Quartz tube

Model 670-206/207

4.Function indicator

5.String

Model 670-208/209/211

6.Control panel

7.Function indicator

8.On/Power button

9.Receiver for remote control signal

10.OFF button

11.Electrical cord

12.Clip

13.Wall mounting bracket

14.Mounting screw

15.Remote control (model 670-208/209/211 only)

I. OFF button

II. On/Power button

Stand components (for models with base only:

a.Base

b.Stand, lower part

c.Screws (x2)

d.Stand, middle part

e.Stand, upper part

f.Thin rod

g.Sleeve

h.Cuff

i.Washer and screw

j.Cord holder

Tent bracket (model 670-209/211 only)

k.Curved bar

l.Bracket, front

m.Bracket, rear

n.Screws and nuts for bracket

o.Mounting screw

A wall bracket together with rawlplugs and screws are included with the wall-mounted model.

Certain models also have remote control and waterproof cover.

POSITIONING THE APPLIANCE

Wall-mounted model (670-206/208)

•The heater head (1) should be at least 30cm from the ceiling,

30 cm from any side wall, and at least 1.8m above the floor.

•Use the wall bracket supplied for wall mounting. Do not use other brackets or fittings.

•Screw wall bracket to wall as illustrated. The angled section of the bracket should face upwards.

•Hang the heater head on the wall bracket. Mount hanging bracket (13) at the top of the rear of the heating head on angled part

of wall bracket. Insert retaining screw in hole in wall bracket base, and tighten securely.

•Check that the appliance is firmly fixed in place before using it.

Models with tent bracket (model 670-209/211)

•The heater head (1) should be at least 30cm from the tent ceiling or parasol cover, 30 cm from any side wall, and at least 1.8m above the floor.

•Use the tent bracket supplied for mounting.

Do not use other brackets or fittings.

•Mount tent bracket front (l) and rear sides (m) on a tent or parasol pole as illustrated. Use the screws and nuts supplied (n).

•Mount curved bar (k) into socket on front of bracket using the retaining screws supplied

(o).

10