ANTENNA/CATV CONNECTIONS
Combination VHF/UHF Antenna | |
Single 75 ohm Cable | |
300 ohm | |
Splitter | Take off the Splitter |
UHF Antenna |
ANT(75)
IN
VIDEO 
OUT
VIDEO
This television has an extended tuning range and can tune most cable channels without using a cable company supplied converter box. Some cable companies offer "premium pay channels" in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler
|
|
| Matching Transformer |
300 ohm | (not supplied) | ||
|
|
|
|
|
|
|
|
L/MONO
L/MONO
AUDIO 
R
device which is generally provided by the cable company.
VHF Antenna
Single 75 ohm Cable
300 ohm | Combiner | |
| (not supplied) | |
Incoming CATV | ||
Matching Transformer | ||
| ||
| (not supplied) |
Converter/ Descrambler
Converter/ Descrambler 
Splitter | A / B Switch A B |
Separate VHF/UHF Antennas
Connect the 75 ohm Cable from the VHF antenna and the UHF antenna
NOTE: If your VHF antenna has a
For Subscribers to Basic Cable TV Service
For basic cable service not requiring a Converter/Descrambler box, connect the CATV 75 ohm Coaxial Cable directly to the Antenna Jack on the back of the television.
For Subscribers to Scrambled Cable TV Service
If you subscribe to a cable service which requires the use of a Converter/Descrambler box, connect the incoming cable to the Converter/Descrambler box and connect the output of the box to the Antenna Jack on the back of the television. Follow the connections shown left. Set the television to the output of the Converter/ Descrambler box (usually channel 3 or 4) and use the Converter/ Descrambler box to select channels.
Combination VHF/UHF Antenna (Single 75 ohm Cable or 300 ohm
Connect the 75 ohm cable from a combination VHF/UHF antenna to the Antenna Jack. If your combination antenna has a 300 ohm Twin- lead Wire, use the
Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm
Connect the UHF
For Subscribers to Unscrambled Basic Cable with Scrambled Premium Channels
If you subscribe to a cable service in which basic cable channels are unscrambled and premium channels require the use of a Converter/Descrambler box, you may wish to use a
AUDIO/VIDEO JACK CONNECTIONS
The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model and features of each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs.
The connection diagrams below are offered as suggestions. You may need to modify them to accommodate your particular assortment of components. The diagrams are intended to show component video and audio interconnections only.
Press the TV/AV selector button to select the AV mode to use the TV as a monitor.
Operate your VCR as usual.
TV/AV SELECTION | 2. To connect the TV to a TV Game |
If you connect the TV to a VCR, camcorder, or TV game, through the audio/video in jacks, use the TV/AV button to make your selection.
Press the TV/AV button repeatedly to select the desired mode. "AUX1" or "AUX2" will display on the screen for 4 seconds.
AUX 1
TV 
AUX 1 
AUX 2 
1. To connect the TV to a VCR
VCR |
| Rear of TV | |
VIDEO | IN | OUT | |
|
|
| |
| AUDIO (L) |
| |
To Audio/Video OUT | AUDIO (R) |
| |
The TV can also be used as a display device for many video games. However, due to the wide variety of different types of signal generated by these devices and subsequent
To Audio/Video OUT
| (MONO) | |
TV GAME | VIDEO IN L – AUDIO IN – R | |
Front of TV | ||
|
(not supplied)
3.To connect the TV to the camcorder
To playback from the camcorder, connect the camcorder to the TV as shown.
| (MONO) |
To AV OUT jack | VIDEO IN L – AUDIO IN – R |
Front of TV |
6
(not supplied)
(not supplied)
6 | 1/8/2002, 12:19 |
