Manuals / Meridian America / Home Audio / Speaker System

Meridian America DSP Loudspeaker Specification - DSP6000 and DSP6000C, Digital inputs and outputs

Models: Meridian DSP

1 49

Download 49 pages 26.96 Kb

Page 15

Specification – DSP6000 and

INTRODUCTION

Specification – DSP6000 and

DSP6000C

Digital inputs and outputs

¥2 x cable inputs, 32-192kHz. FIFO locks at 44.1, 48, 88.2, 96, 176.4, or 192kHz ± 150ppm (176.4 and 192kHz supported by single wire connection and future software upgrade).

¥PCM using IEC958, or MHR connection support with auto-detection.

¥1 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling.

Signal processing

¥2 x Motorola 56303 running at 80MHz.

¥4 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling.

¥Crossovers linear-phase ±30¼ at 200Hz and 2.6kHz.

Output stages

¥Power amplifiers: Complementary bipolar design, with output-stage error correction and twin loop design.

¥Bass: 2 x 75W.

¥Mid: 75W.

¥Treble: 75W.

Acoustic

¥3 way.

¥Separate mid/top plywood cabinet.

¥Bass drive unit: 4 x 200mm (8") high-efficiency long-throw custom drivers.

¥Mid drive unit: 1 x 160mm (6") custom polypropylene driver using phase plug.

¥Treble drive unit: 1 x 25mm (1") Meridian piston in short horn, aluminium dome with silver voice-coil.

10

Image 15

Meridian America DSP Loudspeaker manual Specification - DSP6000 and DSP6000C, Digital inputs and outputs, Signal processing

Contents

U S E R G U I D E M E R I D I A N D S P L O U D S P E A K E RSetup Meridian DSP Loudspeaker User GuidePhase VolumeDesigned and manufactured in the UK by Copyright and acknowledgementsSales and service in the UK Sales and service in the USAContents Service and guarantee TroubleshootingTroubleshooting CleaningIntroduction Meridian DSP loudspeakers Digital Signal ProcessingDSP loudspeaker drivers Mounting options Power amplifiersMeridian High Resolution MHR CabinetMeridian Comms Sample configurations Meridian Digital TheatreMeridian Digital Music System Digital inputs and outputs Specification - DSP5000 and DSP5000CSignal processing CharacteristicsPower ControlCabinet Output stages Specification - DSP5500 DSP5500HC, and DSP5500CSignal processing Digital inputs and outputsControl CharacteristicsPower ¥Noise and hum -94dBrat all volume settingsOutput stages Specification - DSP6000 and DSP6000CSignal processing Digital inputs and outputsControl CharacteristicsPower ¥Noise and hum -94dBrat all volume settingsAvailable accessories Setting up the DSP loudspeakers Unpacking Care when unpackingComponents Caution DSP6000 and DSP6000C only Tightening the drive unitsTo fit the feet except DSP5000C and DSP5500HC ¥Fit a plastic spacer over each pillar Radio interference To obtain the best sound Positioning the digital loudspeakersSafety warnings To avoid overheatingCommunications connections Connecting the loudspeakersBack panel Digital connectionsTo use a DSP loudspeaker as a centre speaker Connecting to other equipmentMeridian surround system To connect three or more DSP loudspeakers in aM5 lead To connect two DSP loudspeakers to a Meridian CDPlayer or other digital source 588 CD PlayerUsing the DSP loudspeakers Selecting a source RadioTo select a source Radio Changing the displayPCM 96k Status indicatorsRadio Adjusting the volumeTo change the volume To restore the soundBass+0.0 Changing the treble, bass, or phasePhase + Tre.+0.0Axis Changing the listening positionBal BalConfiguring the DSP loudspeakers Type L Choosing standard settingsL. Slv To specify the speaker positionTo choose master or slave Specifying information about your system L 500 Auto S.A. P.A. L.E. Bal. Y Centre N Diag. NTo configure the DSP loudspeaker Configuring the sources RD RadioTo configure a source Initial value FF. YRadio OptionFree Boundary Sub.1 Sub.2 Corner Configuring the setup optionsSetup FreeTo store the settings C.FreC.Tilt+1 StoreTroubleshooting There is radio interference TroubleshootingDisplay on front panel not lit Remote not workingUnit stays in standby Only the master loudspeaker playsSound is odd or mono Cleaning DSP6000 and DSP6000C only CleaningService and guarantee ServiceGuarantee TROUBLESHOOTING Index