Manuals / Micro Star Computer / Computer Equipment / Computer Hardware

Micro Star Computer G31M manual Front USB Connector JUSB1 / JUSB2, 2-18, JUSB2/1, USB 2.0 Bracket

Models: G31M

1 116

Download 116 pages 36.59 Kb

Page 32

Image 32

MS-7379 Mainboard

Front USB Connector: JUSB1 / JUSB2

This connector, compliant with Intel® I/O Connectivity Design Guide, is ideal for con- necting high-speed USB interface peripherals such as USB HDD, digital cameras, MP3 players, printers, modems and the like.

JUSB2/1		9	1
JUSB2/1		10	2
		Pin Definition
PIN	SIGNAL		PIN	SIGNAL
1	VCC		2	VCC
3	USB0-		4	USB1-
5	USB0+		6	USB1+
7	GND		8	GND
9	Key(no pin)		10	USBOC

USB 2.0 Bracket

(Optional)

Important

Note that the pins of VCC and GND must be connected correctly to avoid possible damage.

2-18

Page 32

Image 32

Micro Star Computer G31M manual Front USB Connector JUSB1 / JUSB2, 2-18, JUSB2/1, USB 2.0 Bracket, MS-7379 Mainboard

Contents

G52-73791X1 MS-7379 V2.X MainboardG31M Series Copyright Notice TrademarksRevision History Technical SupportSafety Instructions FCC-B Radio Frequency Interference Statement Micro-Star International MS-7379WEEE Waste Electrical and Electronic Equipment Statement Page Page viii CONTENTSPage Getting Started Getting StartedChapter Mainboard Specifications MS-7379 MainboardProcessor Support Supported FSBConnectors Getting Started RAID optionalSlots TPM optionalMainboard Layout G31M Series MS-7379 v2.X M-ATX MainboardMS-7379 Mainboard IntelPacking Checklist Getting StartedChapter Hardware SetupHardware Setup Quick Components Guide MS-7379 MainboardCPU Central Processing Unit Introduction to LGA 775 CPUOverheating Replaceing the CPUCPU & Cooler Installation 3. The pins of socket revealMS-7379 Mainboard 2. Remove the cap from lever hinge side as the arrow showsHardware Setup 5. Lift the load lever up and open the load plate1. Read the CPU status in BIOS Chapter MS-7379 MainboardMemory Dual-Channel mode Population RuleDDR2 Hardware SetupVolt Notch Installing Memory ModulesMS-7379 Mainboard Power Supply ATX 24-Pin Power Connector ATX1ATX 12V Power Connector JPW1 ATX1Back Panel 2-10Mouse/Keyboard Serial PortHardware Setup Audio Ports 2-11Connectors Floppy Disk Drive Connector FDD1IDE Connector IDE1 2-12Serial ATA Connector SATA1/ SATA2/ SATA3/ SATA4 2-13SATA4 SATA3 SATA1 SATA2 Hardware SetupFan Power Connectors CPUFAN1, SYSFAN1 Chassis Intrusion Connector JCI12-14 CPUFAN1S/PDIF-Out Connector JSP1 CD-In Connector CDIN1TPM Module connector JTPM1optional 2-15Front Panel Connectors JFP1, JFP2 2-16JFP1 JFP2Front Panel Audio Connector JAUD1 Parallel Port Header JLPT12-17 JAUD1Front USB Connector JUSB1 / JUSB2 2-18JUSB2/1 USB 2.0 BracketJumpers Clear CMOS Jumper JBAT12-19 JBAT1Slots PCI Peripheral Component Interconnect Express SlotPCI Peripheral Component Interconnect Slot PCI Interrupt Request RoutingChapter BIOS SetupBIOS Setup MS-7379 Mainboard Entering SetupPress DEL to enter SETUP Control Keys Getting HelpGeneral Help F1 Main MenuStandard CMOS Features Advanced BIOS FeaturesPower Management Setup PNP/PCI ConfigurationsBIOS Setup Load Optimized Defaults BIOS Setting PasswordSave & Exit Setup Exit Without SavingStandard CMOS Features Date MMDDYYmonth dateBIOS Setup Device / Vender / Size LBA/Large ModeDMA Mode Hard Disk S.M.A.R.TMS-7379 Mainboard System Information Press Enter to enter the sub-menu, and the following screen appearsAdvanced BIOS Features Boot Sector ProtectionQuick Booting Boot Up Num-Lock LEDCPU Feature Chipset Feature3-10 MS-7379 Mainboard MPS Table VersionBIOS Setup VGA Share Memory Size Boot Sequence1st/ 2nd/ 3rd Boot Device Boot From Other DeviceTPM Enable/Disable status, TPM Owner Status 3-12MS-7379 Mainboard Clearing the TPM These items show the status of TPM read onlyIntegrated Peripherals 3-13USB Controller USB Device Legacy Support3-14 MS-7379 Mainboard On-Chip IDE ControllerPCI IDE BusMaster On-Chip SATA ControllerPower Management Setup ACPI FunctionACPI Standby State BIOS SetupMS-7379 Mainboard Re-Call VGA BIOS from S3 Power Button FunctionRestore On AC Power Loss Wakeup Event Setup3-17 BIOS Setup Resume by PCI-E DeviceResume by RTC Alarm PNP/PCI Configurations PCI Latency Timer3-18 Primary Graphic’s AdapterIRQ 3/4/5/7/9/10/11/14/15 BIOS Setup IRQ Resource Setup3-19 H/W Monitor 3-20Chassis Intrusion CPU/SYS Smart FAN TargetAdjust CPU FSB Frequency Adjust CPU RatioAdjusted CPU Frequency Advance DRAM ConfigurationMS-7379 Mainboard Configuration DRAM Timing by SPD DRAM RAS# to CAS# Delay3-22 DRAM CAS# LatencyBIOS Setup DRAM TWR Adjusted DDR Memory FrequencyAuto Disable DIMM/PCI Frequency 3-23MS-7379 Mainboard 3-241. If you do not have any EMI problem, leave the setting at Disabled for optimal system stability and performance. But if you are plagued by EMI, select the value of Spread Spectrum for EMI reduction BIOS Setup Load Fail-Safe/ Optimized Defaults3-25 MS-7379 Mainboard BIOS Setting Password3-26 Realtek Audio Appendix AInstalling the Realtek HD Audio Driver Installation for Windows 2000/XP/Vista2. Click Realtek HD Audio Driver MS-7379 MainboardRealtek Audio Software Configuration MS-7379 MainboardRealtek Audio Sound EffectEnvironment Simulation Enable / Disable ResetMS-7379 Mainboard Equalizer Selection SaveRaise the key Remove the human voice Lower the key Realtek Audio Frequently Used Equalizer SettingKaraoke Mode 1. Adjust Volume playback multi-streaming and click OK to save the setupMixer 2. Multi-Stream FunctionRealtek Audio A-10 MS-7379 Mainboard 3. Playback controlM ute ToolA-11 4. Recording controlM ute Realtek AudioSpeaker Configuration Audio I/OA-12 MS-7379 MainboardRealtek Audio Connector Settings Disable front panel jack detection optionMute rear panel output when front headphone plugged in Enable auto popup dialogue, when device has been plugged inA-14 MS-7379 Mainboard S/PDIFOutput Sampling Rate Output SourceA-15 Realtek Audio Test SpeakersMS-7379 Mainboard MicrophoneA-16 Realtek Audio 3D Audio DemoA-17 MS-7379 Mainboard InformationA-18 Hardware Setup Connecting the SpeakersA-19 n 2-Channel Mode for Stereo-Speaker Output4-Channel Analog Audio Output A-20MS-7379 Mainboard n 4-Channel Mode for 4-Speaker Output 6-Channel Analog Audio Output A-21Realtek Audio n 6-Channel Mode for 6-Speaker Output 8-Channel Analog Audio Output A-22MS-7379 Mainboard n 8-Channel Mode for 8-Speaker Output Dual Core Center Appendix BActivating Dual Core Center MS-7379 MainboardDual Core Center MainIntroduction Temperature AV/ Game/ Office/ Silence/ CoolSharp mode Smooth mode Clock VoltageDOT Dynamic OverClocking Dual Core CenterClock MS-7379 MainboardVoltage Dual Core CenterFAN Speed MS-7379 MainboardTemperature Dual Core CenterMS-7379 Mainboard User ProfileB-10 B-11 Dual Core CenterIntel ICH7R SATA RAID Appendix CICH7R Introduction MS-7379 MainboardBIOS Configuration Using the Intel Matrix Stroage Manager Option ROM1. Creating, Deleting and Resetting RAID Volumes Intel ICH7R SATA RAID1 Create RAID Volume MS-7379 MainboardIntel ICH7R SATA RAID MS-7379 Mainboard 2 Delete RAID Volume Intel ICH7R SATA RAID3 Reset Disks to Non-RAID MS-7379 MainboardInstalling Software Install Driver in Windows XP† New Windows XP / 2000 Installation † Existing Windows XP/2000 Driver InstallationInstallation of Intel Matrix Storage Console C-10Click on this item MS-7379 MainboardC-11 Intel ICH7R SATA RAIDC-12 MS-7379 MainboardC-13 Intel ICH7R SATA RAIDMS-7379 Mainboard C-14Once the installation is complete, the following window appears Intel ICH7R SATA RAID RAID Migration InstructionsC-15 MS-7379 Mainboard Create RAID Volume from Existing DiskC-16 Intel ICH7R SATA RAID 1 Step 1 Configure Volume † RAID Volume NameC-17 † RAID LevelC-18 † Strip Sizes2 Select the source disk MS-7379 MainboardC-19 Intel ICH7R SATA RAID 3 Select Member Hard DrivesC-20 MS-7379 Mainboard 4 Specify Volume Size5 Start Creating RAID Volume from Existing Hard Drive Wizard C-21 Intel ICH7R SATA RAID 6 Start MigrationDegraded RAID Array Missing Hard Drive MemberFailed Hard Drive Member C-22C-23 5. Exit Intel RAID Option ROM, and then reboot to Windows system6. When prompted to rebuild the RAID volume, click Yes Intel ICH7R SATA RAID