Manuals
/
Micron Technology
/
Household Appliance
/
Fan
Micron Technology
Turbofan instruction manual Instruction manual and installation guide
Models:
Turbofan
1
1
28
28
Download
28 pages
37.76 Kb
1
2
3
4
5
6
7
8
<
>
Specs
Install
Turbofan Parts Diagram
Maintenance
4.2.1Hydraulic Configuration
5.2Calibration Procedure
Calibration And Adjustment
If a new sprayer is being designed or an original pump is to be replaced, it is suggested that a diaphragm or centrifugal type is chosen. This should be able to provide a pressure of about 1 – 3 bar 15 – 45 psi and should be capable of delivering the maximum flow rate of the sprayer plus the flow required for tank agitation if a mechanical agitator is not used. An output of 60 l/min is satisfactory for most low volume sprayers without mechanical agitation
Safety
Page 1
Image 1
TURBOFAN
Instruction manual and installation guide
Micron Sprayers Limited
Bromyard Industrial Estate
Bromyard, Herefordshire
HR7 4HS, UK
Tel: +44 (0) 1885 482397
Fax:+44 (0) 1885 483043
E-mail:
micron@micron.co.uk
URL: http://www.micron.co.uk
Page 2
Page 1
Image 1
Page 2
Contents
TURBOFAN
Instruction manual and installation guide
Micron Sprayers Limited
Bromyard Industrial Estate
CONTENTS
DRAFT
1.0 INTRODUCTION
DRAFT
2.0 SPECIFICATION
Figure 1. Turbofan spray head
DRAFT
3.0 TEN KEY POINTS FOR USERS
DRAFT
4.0 INSTALLATION
4.1Mounting of Sprayheads
4.1.2Spacing of Sprayheads
DRAFT
DRAFT 4.1.3Angle of Sprayheads
4.2.1Hydraulic Configuration
4.2Hydraulic System
4.2.3Series Connection
DRAFT 4.2.2Parallel Connection
4.2.4Hydraulic Oil Flow
DRAFT
4.2.5Hydraulic Pressure and Hose Size Selection
DRAFT
TABLE 1 – Pressure drop along
hydraulic hoses
HOSE SIZE
Page
4.2.8 Pressure Surge Prevention
DRAFT 4.2.7System Protection
4.2.9Speed Regulation
4.2.10 Hydraulic Oil
PRESSURE GAUGE
CLOSED CENTRE SYSTEM
OPEN CENTRE SYSTEM
DRAFT
PRESSURE GAUGE PRESSURE LINE FROM TRACTOR
4.3Spray Liquid
DRAFT 4.2.13Filter
DRAFT
If a new sprayer is being designed or an original pump is to be replaced, it is suggested that a diaphragm or centrifugal type is chosen. This should be able to provide a pressure of about 1 – 3 bar 15 – 45 psi and should be capable of delivering the maximum flow rate of the sprayer plus the flow required for tank agitation if a mechanical agitator is not used. An output of 60 l/min is satisfactory for most low volume sprayers without mechanical agitation
5.2Calibration Procedure
4.4Testing
DRAFT
5.1 Daily inspection
DRAFT
6.0 HEALTH AND SAFETY
5.4Sequence of Operation
5.5After Use
DRAFT
7.0 CALIBRATION AND ADJUSTMENT
7.1 Application Rate
Figure 9. Coverage of sprayer
DRAFT
Table 2 – Coverage of sprayer in ha/min
Example
DRAFT
16 l/min from sprayer
Output
DRAFT
8.0 MAINTENANCE
Each day after spraying
8.2 Dismantling of Sprayhead
2.Remove atomiser 1 by unscrewing screw
DRAFT
PART NO
DRAFT
DESCRIPTION
MICRON ATOMISER PARTS TBF/003
DRAFT
TURBOFAN PARTS DIAGRAM
APPENDIX A
A E B D C