MicroNet Technology SP3508A 5.9.1 Basic

Support Protocol-based VLAN

In order for an end station to send packets to different VLAN, it has to be

either capable of tagging packets with VLAN tags or attached to a VLAN-

aware bridge that is capable of classifying and tagging the packet with

different VLAN ID based on not only default PVID but also other information

about the packet, such as the protocol. VDSL Switch will support protocol-

based VLAN classification by means of both built-in knowledge of layer 2

packet formats used by selected popular protocols, such as Novell IPX and

AppleTalk’s EtherTalk, and some degree of programmable protocol matching

capability.

5.9.1 Basic

This interface allows users to assign VLAN membership to each port. The

procedure for setting VLAN member is as follow.

1. From the main menu, under ‘Administrator’, click on <VLAN

config>.

2. Click <Add>.

3. Type a VID (Valid Range: 2-4094). The default is 1.

4. From the Available ports box, select ports to add to the VLAN and

click <Add>.

5. Click <Apply>.

26

Contents

Main Users Manual 8-Port VDSL Managed Switch Model No.: SP3508A Table of Contents Page Chapter 1 Introduction 1.1 Package Contents 1.2 Key Features Page Chapter 2 Installation 2.1 Hardware Installation 2.2 Pre-installation Requirements 2.3 Cabling Requirements 2.4 Connecting to Gigabit Ethernet 2.5 Connecting to RJ-11 Chapter 3 Physical Description 3.1 LED Definition 3.2 Switch Connectors Chapter 4 IP Address Configuration 4.1 Out-Band Access 4.1.1 Console Port Page Page 4.2 Remote Access 4.2.1 Telnet 4.2.2 Web-Based UI Page Page 5.3 Port Statistics 5.4 IP Address 5.5 Switch Setting 5.5.1 Basic Hardware Version Default config value version 5.5.2 Advanced The interface allow advance configuration of the VDSL Switch. Priority Queue Service Settings Protocol Enable Setting Auto Speed SNR margin value setup 5.6 Port Controls 5.7 Link Aggregation 5.7.1 Aggregator Setting 5.7.2 Aggregator Information 5.7.3 State Activity 5.8 Filter Database 5.8.1 IGMP Snooping 5.8.2 Static MAC Address 5.8.3 Port Security 5.8.4 MAC Filtering 5.9 VLAN Configuration 5.9.1 Basic 5.9.2 Port VID 5.10 Spanning Tree 4. The following parameter can be configured on each port and click <Apply> button to modify. Parameter Description Port Priority Path Cost 5.11 Port Sniffer 5.12 SNMP Page 5.13 Signal to Noise Ratio 5.14 Security Manager 5.15 TFTP Update Firmware 5.16 Configuration Backup 5.16.1 TFTP Restore Configuration 5.16.2 TFTP Backup Configuration 5.17 Reset and Rebooting System Chapter 6 Application Chapter 7 Appendix 7.1 Appendix A: Specifications Humidity 10% ~ 90% non-condensing Page 7.2 Appendix B: Troubleshooting 7.3 Appendix C: System Diagnostics 7.3.1 Power and Cooling Problems 7.3.2 Installation 7.3.3 Transmission Mode 7.3.4 Cabling 7.3.5 Physical Configuration 7.3.6 System Integrity 7.4 Appendix D: VDSL Spectrum VDSL Technology Requirements & Definitions 7.5 Appendix E: Example of VLAN Setting 7.5.1 Port-Based VLAN Setting 7.5.2 Tag-Based (IEEE 802.1Q) VLAN Setting