Milan Technology MIL-W2332G Appendix A: Default Settings

55

Appendix A: Default Settings

TIP: Press the Default (SF-Reset, or Soft-Reset) switch on the housing of a pow-

ered-on AP to reset the configuration settings to factory-default values.

Setting Name Default Value

Global

User Name root

Password root

IEEE 802.11g

Regulatory Domain FCC (U.S.)

Channel Number 11

SSID wireless

SSID Broadcasts Enabled

Transmission Rate Auto

Transmit Power High

MAC Address See the label on the accompanying

PCMCIA card or the label on the

housing of the AP.

Security Mode Open System

Selected WEP Key Key #1

WEP Key #1 00-00-00-00-00

WEP Key #2 00-00-00-00-00

WEP Key #3 00-00-00-00-00

WEP Key #4 00-00-00-00-00

MAC-Address-Based Access

Control Disabled

Access Control Table Type Inclusive

Wireless Client Isolation Disabled

AP Load balancing Disabled

Link Integrity Disabled

Association Control

Max Number of Clients 64

Block Clients if Traffic

Load Exceeds Disabled

LAN Interface

Method of obtaining an IP Ad-

dress Set manually

IP Address 192.168.1.254

Subnet Mask 255.255.255.0

Default Gateway 0.0.0.0

DHCP Server Disabled

Management

UPnP Enabled

Contents

Main Page i Federal Communication Commission Interference Statement FCC Radiation Exposure Statement R&TTE Compliance Statement Table of Contents Page Page 1. Introduction 1.1 Overview 1.2 Features Page Management 1.3 LED Definitions 2. First-Time Installation and Configuration 2.1 Selecting a Power Supply Method 2.2 Mounting the AP on a Wall 2.3 Preparing for Configuration 2.3.1 Connecting the Managing Computer and the AP 2.3.2 Changing the TCP/IP Settings of the Managing Com- puter 2.4 Configuring the AP 2.4.1 Entering the User Name and Password 2.4.2 Step 1: Selecting an Operational Mode AP/Bridge. This mode provides both Access Point and Static LAN-to-LAN Bridging STA-AP. This type of wireless link is established between an IEEE 802.11 Station WDS. This type of wireless link is established between two IEEE 802.11 APs. Wire- 2.4.3 Step 2: Configuring TCP/IP Settings 2.4.4 Step 3: Configuring IEEE 802.11 Settings 2.4.5 Step 4: Reviewing and Applying Settings 2.5 Deploying the AP Page 2.6 Setting up Client Computers 2.6.1 Configuring IEEE 802.11g-Related Settings 2.6.2 Configuring TCP/IP-Related Settings 2.7 Confirming the Settings of the AP and Client Computers 2.7.1 Checking if the IEEE 802.11g-Related Settings Work 2.7.2 Checking if the TCP/IP-Related Settings Work Page Page 3.1.1 Menu Structure Home. For going back to the start page. Status. Status information. General. Global operations. TCP/IP. TCP/IP-related settings. Page 3.1.2 Save, Save & Restart, and Cancel Commands 3.1.3 Home and Refresh Commands 3.2 Viewing Status 3.2.1 Associated Wireless Clients 3.2.2 Current DHCP Mappings 3.2.3 System Log 3.2.4 Link Monitor 3.3 General Operations 3.3.1 Specifying Operational Mode AP/Bridge. This mode provides both Access Point and Static LAN-to-LAN STA-AP. This type of wireless link is established between an IEEE 802.11 Sta- WDS. This type of wireless link is established between two IEEE 802.11 APs. 3.3.2 Changing Password 3.3.3 Managing Firmware 3.3.3.1 Upgrading Firmware by HTTP 3.3.3.2 Backing up and Restoring Configuration Settings by HTTP 3.3.3.3 Upgrading Firmware by TFTP Page 3.3.3.4 Backing up and Restoring Configuration Settings by TFTP 3.3.3.5 Resetting Configuration to Factory Defaults 3.4 Configuring TCP/IP Related Settings 3.4.1 Addressing 3.4.2 DHCP Server 3.4.2.1 Basic 3.4.2.2 Static DHCP Mappings 3.5 Configuring IEEE 802.11g-Related Settings 3.5.1 Communication 3.5.1.1 Basic 3.5.1.2 Link Integrity 3.5.1.3 Association Control 3.5.1.4 AP Load Balancing 3.5.1.5 Wireless Distribution System LAN Page Page Page Page 3.5.2 Security 3.5.2.1 Basic Page Page 3.5.2.2 MAC-Address-Based Access Control Page 3.5.3 IEEE 802.1x/RADIUS Internet Page 3.6 Configuring Advanced Settings 3.6.1 Packet Filters 3.6.1.1 Ethernet Type Filters 3.6.1.2 IP Protocol Filters 3.6.1.3 TCP/UDP Port Filters 3.6.2 Management 3.6.2.1 UPnP Page 3.6.2.3 SNMP Appendix A: Default Settings Page Appendix B: Troubleshooting B-1: Wireless Settings Problems B-2: TCP/IP Settings Problems B-3: Unknown Problems Appendix C: Additional Information C-1: Firmware Upgrade Using Xmodem Upgrade