Manuals / Miller Electric / Power Tools / Welder

Miller Electric 1000, 1250 manual Symbol Usage, Arc Welding Hazards, Electric Shock can kill

Models: 1250 1000

1 40
Download 40 pages 18.36 Kb
Page 5
Image 5

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING

som _8/03

1-1. Symbol Usage

Means Warning! Watch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols.

YMarks a special safety message.

.Means “Note”; not safety related.

1-2. Arc Welding Hazards

YThe symbols shown below are used throughout this manual to call attention to and identify possible hazards. When you see the symbol, watch out, and follow the related instructions to avoid the hazard. The safety information given below is only a summary of the more complete safety information found in the Safety Standards listed in Section 1-5.Read and follow all Safety Standards.

YOnly qualified persons should install, operate, maintain, and repair this unit.

YDuring operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks or severe burns. The electrode and work circuit is electrically live whenever the output is on. The input power circuit and machine internal circuits are also

live when power is on. In semiautomatic or automatic wire welding, the wire, wire reel, drive roll housing, and all metal parts touching the welding wire are electrically live. Incorrectly installed or improperly grounded equipment is a hazard.

DDo not touch live electrical parts.

DWear dry, hole-free insulating gloves and body protection.

DInsulate yourself from work and ground using dry insulating mats or covers big enough to prevent any physical contact with the work or ground.

DDo not use AC output in damp areas, if movement is confined, or if there is a danger of falling.

DUse AC output ONLY if required for the welding process.

DIf AC output is required, use remote output control if present on unit.

DDisconnect input power or stop engine before installing or servicing this equipment. Lockout/tagout input power according to OSHA 29 CFR 1910.147 (see Safety Standards).

DProperly install and ground this equipment according to its Owner’s Manual and national, state, and local codes.

DAlways verify the supply ground − check and be sure that input power cord ground wire is properly connected to ground terminal in disconnect box or that cord plug is connected to a properly grounded receptacle outlet.

DWhen making input connections, attach proper grounding conduc- tor first − double-check connections.

DFrequently inspect input power cord for damage or bare wiring − replace cord immediately if damaged − bare wiring can kill.

DTurn off all equipment when not in use.

DDo not use worn, damaged, undersized, or poorly spliced cables.

DDo not drape cables over your body.

This group of symbols means Warning! Watch Out! possible ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the hazards.

DIf earth grounding of the workpiece is required, ground it directly with a separate cable.

DDo not touch electrode if you are in contact with the work, ground, or another electrode from a different machine.

DUse only well-maintained equipment. Repair or replace damaged parts at once. Maintain unit according to manual.

DWear a safety harness if working above floor level.

DKeep all panels and covers securely in place.

DClamp work cable with good metal-to-metal contact to workpiece or worktable as near the weld as practical.

DInsulate work clamp when not connected to workpiece to prevent contact with any metal object.

DDo not connect more than one electrode or work cable to any single weld output terminal.

SIGNIFICANT DC VOLTAGE exists after removal of input power on inverters.

DTurn Off inverter, disconnect input power, and discharge input capacitors according to instructions in Maintenance Section before touching any parts.

FUMES AND GASES can be hazardous.

Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health.

DKeep your head out of the fumes. Do not breathe the fumes.

DIf inside, ventilate the area and/or use exhaust at the arc to remove welding fumes and gases.

DIf ventilation is poor, use an approved air-supplied respirator.

DRead the Material Safety Data Sheets (MSDSs) and the manufacturer’s instructions for metals, consumables, coatings, cleaners, and degreasers.

DWork in a confined space only if it is well ventilated, or while wearing an air-supplied respirator. Always have a trained watch- person nearby. Welding fumes and gases can displace air and lower the oxygen level causing injury or death. Be sure the breath- ing air is safe.

DDo not weld in locations near degreasing, cleaning, or spraying op- erations. The heat and rays of the arc can react with vapors to form highly toxic and irritating gases.

DDo not weld on coated metals, such as galvanized, lead, or cadmium plated steel, unless the coating is removed from the weld area, the area is well ventilated, and if necessary, while wearing an air-supplied respirator. The coatings and any metals containing these elements can give off toxic fumes if welded.

OM-2223 Page 1

Page 4 Page 6
Page 5
Image 5
Miller Electric 1000, 1250 Symbol Usage, Arc Welding Hazards, Electric Shock can kill, Fumes and Gases can be hazardous
Page 4 Page 6

1250, 1000 specifications

Miller Electric is a renowned name in the welding and fabrication industry, providing high-quality machines and equipment that cater to a range of applications. Among its impressive line of products are the Miller Electric 1000 and 1250 arc welding machines, designed to offer exceptional performance in both industrial and commercial environments.

One of the main features of the Miller Electric 1000 model is its robust construction, making it ideal for heavy-duty welding tasks. It boasts a powerful output that provides a significant range of welding power, accommodating various electrode sizes and types. This flexibility allows for effective use in a variety of welding processes, including Stick, TIG, and MIG, ensuring that users can tackle a wide array of jobs without needing multiple machines.

The Miller Electric 1250 takes things a step further, delivering even more power and efficiency. With advanced inverter technology, the 1250 offers increased duty cycles and improved energy efficiency, which can lead to cost savings over time. The inverter design also allows for a lighter weight compared to traditional transformer-based machines, enhancing portability and ease of use on job sites.

Both models are equipped with intuitive digital controls and advanced monitoring systems, allowing users to make precise adjustments easily. Features like the Auto-Set functionality simplify the setup process, enabling welders to select materials and thicknesses, and the machine automatically adjusts parameters for optimal results. This is especially beneficial for those who may not have extensive experience, providing a level of confidence in achieving high-quality welds.

Another important characteristic of both the 1000 and 1250 is their adaptability to different environments. They are designed to withstand challenging conditions, including extreme temperatures and dust, making them suitable for outdoor applications and remote job sites. Additionally, Miller Electric prioritizes user safety and comfort, incorporating features like integrated thermal overload protection and ergonomic designs that reduce operator fatigue during prolonged use.

In summary, the Miller Electric 1000 and 1250 arc welding machines represent the pinnacle of modern welding technology. With their powerful output, advanced features, and durable construction, they are well-suited for a range of industrial applications. Whether for routine maintenance or heavy fabrication tasks, these machines deliver reliability and precision, essential for any professional welder.