Setting Sequence Parameters | Miller Electric Axcess specs

SECTION 6 − SETTING SEQUENCE PARAMETERS

6-1. Sequence Parameters In A Program

				Sequence		Parameters





					Volts/Trim	IPM		Seconds

			1.	Preflow				Off-5.0

			2.	Postflow				Off-5.0

			3.	Start	10.0-44.0/	40-1400/		Off-5.0
			3.	Start	0-99	0-99		Off-5.0
					0-99	0-99

			4.	Crater	10.0-44.0/	40-1400/		Off-5.0
			4.	Crater	0-99	0-99		Off-5.0
					0-99	0-99

.For more information on

Sequence mode, see Feeder Set Up Push Button in Section 5-7.

If time is set to Off in Weld sequence, welding continues until gun trigger is released.

If time is set to zero in any timed sequence except Weld, the sequence is skipped.

.Maximum IPM may actually

be lower depending on wire size and gas combination.

X = Setting available.

				Weld
				Crater
				Time
		Start
	Preflow	Time			Postflow
	Preflow				Postflow
	Time				Time
					Time
						Time
Preflow		Start	Weld	Crater	Postflow	Sequence
						End
Trigger				Trigger
Pressed				Released

OM-211 076 Page 24

Image 28

Miller Electric Axcess manual Setting Sequence Parameters, Sequence Parameters In a Program

Contents

OM-211 076H ProcessesDescription File Advanced Manufacturing Systems From Miller to You Table of Contents Page Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can kill ARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or kill California Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier LE Soudage peut provoquer un Incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures graves Risque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessures Principales normes de sécurité En ce qui concerne les stimulateurs cardiaques − Installation Specifications− Introduction Selecting a Location Connection Diagram Rear Panel Connections And Rotating Drive Assembly Pin Network Receptacle Information Gun Recommendation Table Installing And Threading Welding Wire Feeder Display At Power Up Dual Schedule Switch OptionPower Source Upper Display Lower Display Voltage Range Upper Display Lower Display − Operation Operational Terms Power Switch See Section Program Volts Time Arc Adjust Front Panel ControlsSee Section Volts Arc Adjust Program Push ButtonUpper Display Upper Display Lower Display Adjust Control Feeder Set Up Push ButtonSequence Trigger Control Trigger Hold Feeder Set Up Process Set Up Push Button Make a selection, rotate the Adjust control Welding and to preset gas pressure at the regulator Jog/Purge Push Button Adjust Control Gun Trigger ReceptacleJog/Purge Reset Mode PulseMild Steel Accu-pulse Sequence Parameters In a Program − Setting Sequence ParametersSequence Parameters − Maintenance Routine Maintenance Diagnostics Closed error Indicates a trigger Disconnect power before troubleshooting TroubleshootingTrouble Remedy OM-211 076 − Electrical Diagram Circuit Diagram 211 005-E − Parts List − Fig 21 − Fig Part Description Quantity Control Box PLG4 Drive Assembly, Wire 1.2 mm 1.4 mmPage Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s