5-9. Power Source Selection Menu
Non-CE Model Shown
1
Program | Volts | Time (sec) | |
| |||
| Wire Speed | Amps | |
Start |
|
| 2 |
|
|
| |
Crater |
|
| Trigger Hold |
Pre/Postflow |
|
| Dual Schedule |
SequenceAdjustSetup
* * Power Source | Upper Display | Lower Display | Voltage Range | |
|
|
|
|
|
Deltaweld 452 | dELT | 452 | Vmin =10 | Vmax =38 |
Deltaweld 302 | dELT | 302 | Vmin =10 | Vmax =32 |
Deltaweld 652 | dELT | 652 | Vmin =10 | Vmax =44 |
Dimension 302 | dIM | 302 | Vmin =10 | Vmax =32 |
Dimension 452 | dIM | 452 | Vmin =10 | Vmax =38 |
Dimension 652 | dIM | 652 | Vmin =10 | Vmax =65 |
|
|
|
|
|
Dimension 1000 | dIM | 1000 | Vmin =10 | Vmax =60 |
|
|
|
|
|
XMT 304 | XMT | 304 | Vmin =10 | Vmax =35 |
|
|
|
|
|
XMT 456 | XMT | 456 | Vmin =10 | Vmax =38 |
|
|
|
|
|
Invision 354MP | I354 | MP | Vmin =10 | Vmax =35 |
|
|
|
|
|
Invision 456MP | I456 | MP | Vmin =10 | Vmax =38 |
|
|
|
|
|
Invision 456P | I456 | P | Vmin =10 | Vmax =38 |
|
|
|
|
|
PHOENIX 456 | PHX | 456 | Vmin =10 | Vmax =38 |
|
|
|
|
|
SUMMITARC 1000 | SUM | 1000 | Vmin =25 | Vmax =44 |
|
|
|
|
|
|
|
|
|
|
**For any power sources not listed, pick a matching voltage range, or see Sec
1Upper Display
2Lower Display
.When the feeder is turned on,
the Power Source Selection Menu allows the operator to se- lect a default power source. Selecting a default power source, automatically sets the correct Vmin and Vmax set- tings for adjusting the output voltage of the power source.
First Time Feeder Is Turned On
The feeder automatically goes into the Power Source Selection Menu. The feeder displays “dELT” on the Upper Display and “452” on the Lower Display, meaning that a Del- taweld 452 is the default power source, and has a voltage range of 10V as Vmin and 38V as Vmax.
At power up, the operator has three seconds to select a default power source from the list shown on the display. Operator may scroll through the list of power sources by using the Adjust control. After se- lecting a power source the operator has three seconds to change to a different power source or begin welding. After making a power source selection, the operator may press the Program Button to avoid having to wait the three seconds. When turning off the feeder, the de- fault power source will be retained.
If voltage settings have already been set with the Vmin and Vmax in the Auxiliary Menu, selecting a de- fault power source with the Power Source Selection Menu overrides the Vmin and Vmax voltage set- tings.
Next Time Feeder Is Turned On
The feeder will display the last se- lected default power source. The operator has three seconds to se- lect another power source, or press the Program Button to exit the Pow- er Source Selection Menu.
Disabling The Power Source Selection Menu
Once the default power source has been selected the Power Source Selection Menu may be disabled using the Auxiliary Menus. See Section
