Duty Cycle And Overheating, Minutes | Miller Electric EXTREME 360

3-3. Duty Cycle And Overheating

Duty Cycle is percentage of 10 min- utes that unit can weld at rated load without overheating.

If unit overheats, output stops, a Help message is displayed and cooling fan runs. Wait fifteen min- utes for unit to cool. Reduce amper- age or voltage, or duty cycle before welding.

. Single Phase Operation: The

unit is supplied with a 8 AWG power cord. The rated output with 8 AWG is 300 amps, 32 volts at 40% duty cycle. To achieve 60% duty cycle change cord to 6 AWG.

NOTICE − Exceeding duty cycle can damage unit and void warranty.

60% Duty Cycle

6 Minutes Welding	4 Minutes Resting
Overheating	A or V
0	A or V
	15
	OR
Minutes	Reduce Duty Cycle
Minutes

Ref. 216 568-A

Notes

OM-229 409 Page 12

Page 16

Image 16

Miller Electric EXTREME 360 manual Duty Cycle And Overheating, 60% Duty Cycle, Minutes Welding Minutes Resting

Contents

OM-229 409E ProcessesDescription 2007−11Page Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burns Fumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyes Welding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injury Principal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical Devices Symboles utilisés UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesser LES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-229 409 Specifications CC ModeCV Mode − Introduction Duty Cycle And Overheating 60% Duty CycleMinutes Welding Minutes Resting Overheating Dimensions And Weight − InstallationSelecting a Location Connecting 1-Phase Input Power =GND/PE Earth Ground Connecting 3-Phase Input Power Electrical Service Guide Single-Phase Input VoltageInput Amperes At Rated Output Min Grounding Conductor Size In AWG/Kcmil ARC Welding can cause Electromagnetic Interference Weld Output Receptacles And Selecting Cable Sizes350 ft 400 ft Put terminals Remote 14 Receptacle Information Socket Information Operation Optional Gas Valve Operation And Shielding Gas ConnectionGas flow starts with remote contac- tor on − Operation Power SwitchFront Panel Controls Mode Switch Settings Mode Meter Reading At Idle Meter Reading While WeldingMode Switch Setting Process Output On/Off Control Meter Functions Stick Start Procedure Lift-Arc TIG ProcedureLow OCV Stick Do not remove case when blowing out inside of unit − Maintenance & TroubleshootingBlowing Out Inside Of Unit Troubleshooting Voltmeter/Ammeter Help Displays Start Your Professional Welding Career Now − Electrical Diagram Circuit Diagram 211 328-F − Parts List Parts Assembly PLG1 PLG13 174 Knob, Pointer .840 Dia X .250 Id W/Spring Clip−.21 212 Start Your Professional Welding Career Now SOCKET/WRENCH Selection Table Standard Metric Material Thickness Gauge Warranty Owner’s Record

3-3. Duty Cycle And Overheating

. Single Phase Operation: The

60% Duty Cycle

6 Minutes Welding

4 Minutes Resting

Overheating

Minutes

OM-229 409 Page 12