Directives, Standards, Decwire2/04 | Miller Electric OM-220 390F

Declaration of Conformity for

European Community (CE) Products

Note This information is provided for units with CE certification (see rating label on unit).

Manufacturer:	European Contact:
Miller Electric Mg. Co.	Mr. Danilo Fedolfi,
1635 W. Spencer St.	Managing Director
Appleton, WI 54914 USA	MILLER Europe S.r.l.
Phone: (920) 734-9821	Via Privata Iseo 6/E
	20098 San Giuliano
	Milanese, Italy
	Phone: 39(02)98290-1
	Fax: 39(02)98290203

European Contact Signature:

Declares that the product: AxcessE Wire Feeder

conforms to the following Directives and Standards:

Directives

Low Voltage Directive: 73/23/EEC

Electromagnetic Compatibility (EMC) Directive: 89/336/EEC

Machinery Directives: 98/37/EEC, 91/368/EEC, 92/31/EEC, 133/04, 93/68/EEC

Standards

Arc Welding Equipment − Part 5: Wire Feeders. IEC 60974-5 Ed. 1

Arc Welding Equipment − Part 10: Electromagnetic Compatibility (EMC) Requirements. IEC 60974-10 August 2002

Arc Welding Equipment − Part 1: Welding Power Sources. IEC 60974-1 Ed. 2.1

Degrees Of Protection Provided By Enclosure (IP Code) IEC 60529 Ed. 2.1

Insulation Coordination For Equipment Within Low-Voltage Systems −

Part 1: Principles, Requirements and Tests: IEC 60664-1 Ed. 1.1

Arc Welding Equipment − Part 5: Wire Feeders. IEC 60974-5 Ed. 1

dec_wire_2/04

Image 4

Miller Electric OM-220 390F manual Directives, Standards, Decwire2/04

Contents

OM-220 390F ProcessesDescription File Advanced Manufacturing Systems From Miller to You Table of Contents Directives Decwire2/04Standards Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can kill ARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or kill California Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier LE Soudage peut provoquer un Incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures graves Risque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessures Principales normes de sécurité En ce qui concerne les stimulateurs cardiaques − Definitions Disconnect input plug or power before working on machineKeep your head out of the fumes Symbols And Definitions Manufacturer’s Rating Label For CE Products − Installation Specifications− Introduction Selecting a Location Connection Diagram Rear Panel Connections And Rotating Drive Assembly Pin Network Receptacle Information Gun Recommendation Table Installing And Threading Welding Wire Feeder Display At Power Up Dual Schedule Switch OptionPower Source Upper Display Lower Display Voltage Range Net Wait − Operation Operational Terms Power Switch See Front Panel SectionsSee Section Program Push Button Upper Display Lower Display Amps LED Feeder Set Up Push Button Adjust Knob Process Set Up Push Button ProcessSetup Jog/Purge switch provides the following functions Jog/Purge Push Button Adjust Knob Gun Trigger ReceptacleJog/Purge Reset Mode PulseMild Steel Accu-pulse Sequence Parameters In a Program − Setting Sequence ParametersSequence Parameters − Maintenance Routine Maintenance Diagnostics Closed error Indicates a trigger Disconnect power before troubleshooting TroubleshootingTrouble Remedy OM-220 390 − Electrical Diagram Circuit Diagram 211 005-E − Parts List − Fig 21 − Fig 10-2 Part Description Quantity Control Box PLG4 Drive Assembly, Wire Drive Assembly, Wire -1Item 1.2 mm Metric1.4 mm Page Page Page Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s