SYMBOLOGY
Read Operator’s Manual
Double insulation
Earth
Danger, Warning, or Caution
-Consult the operators manual for additional safety information.
|
|
|
|
| Risk of electrical shock - To |
|
|
|
|
| avoid electric shock, remove |
|
|
|
|
| test leads before opening bat- |
|
|
|
|
| tery door |
|
|
|
|
| Battery compartment |
|
|
|
|
|
|
|
|
|
|
| European Conformity Mark |
|
|
|
|
|
|
|
|
|
|
| Underwriters Laboratories, Inc., |
|
|
|
|
| United States and Canada |
|
|
|
|
|
|
Cat IV | Classification of transient | ||||
overvoltages, based on | |||||
|
|
|
|
| nominal line voltage to earth. |
|
|
|
|
| Do not dispose of this product |
|
|
|
|
| |
|
|
|
|
| |
|
|
|
|
| as unsorted municipal waste. |
FUNCTIONAL DESCRIPTION
1. | Display | 9 | 8 | 7 |
2. | Worklight button |
| ||
|
|
| ||
3. | Power button |
|
|
|
4. | Function switch |
|
|
|
| (Cat.No. 2213 only) | 1 |
|
|
5. | COM Terminal input |
|
| |
2 |
|
| ||
6. | Ω Terminal input |
|
| |
7. | Indicator |
|
|
|
8. | LED Worklight | 3 |
|
|
9. | Indicator |
|
| |
10. Probe storage |
|
|
| |
11. Grips | 4 |
|
| |
12. Accessory bay |
|
| ||
|
|
| ||
12 | 5 |
| 6 | |
|
|
| ||
| 11 |
|
|
|
| 10 |
|
|
|
ASSEMBLY
WARNING To avoid an electrical hazard, turn the tester OFF and disconnect the test leads before replacing batteries.
Loading/Changing the Batteries
Replace batteries when the Low Battery indicator is displayed.
1.Press the Power ON/OFF button to turn off the tester. Disconnect the test leads.
2. Unscrew and remove battery door.
3. Insert two (2) AAA batteries, according to the polarity marked in the battery compartment
4. Close the battery door and tighten two (2) screws securely.
Installing/Removing the Belt Clip
The belt clip can be removed/installed into the accessory bay. Line up the belt clip and secure with the accessory bay screw.
Storage
To store the leadwires when not in use, rotate the belt clip 90°. Wrap the leadwires around the body of the tester. Rotate the belt clip down to hold the leadwires in place.
Probe Tip Sleeves
Measurement Category and Voltage Rating of the Test Leads:
Probe Tip Sleeves ON: Cat IV, 600V / CAT III 1000V
Probe Tip Sleeves OFF: Cat II 1000V
To remove the probe tip sleeves:
1.Disconnect the test leads from the tester.
2.Grasp the probe firmly in one hand.
3.Hold the probe tip sleeve firmly with the other hand.
4.Pull to remove the probe tip sleeve to expose more of the probe tip.
5.Push probe tip sleeve back onto probe tip when not in use.
OPERATION
WARNING Only use Milwaukee test leads with the MILWAUKEE Tester. Inspect test leads for continuity before each use. Do not use if the readings are high or noisy.
LCD Backlight
The LCD backlight will turn off about 20 seconds after
LED Worklight
Press the Worklight Button to turn the LED on and off. The worklight will turn off automatically after about 1 minute. It is not necessary to turn on the Tester to use the worklight.
Making a Measurement
The tester is designed to auto range at all times. With Auto Ranging, the tool will automatically select the range with the best resolution
The Tester automatically switches from Voltage AC/ DC measurement to Continuity when no voltage is present. The tool will automatically identify VAC from VDC and will indicate which on the display.
Hazard Voltage Warning
If measured voltage is over AC/DC 35 V, the
Indicator LED will be lit RED and the buzzer will sound with steady, intermittent beeps (B_B_B).
If measured voltage exceeds the measuring range (over approximately 600V), the and Indicator LEDs flash rapidly, alternating RED and YELLOW. The buzzer will sound with bursts of three repeating beeps (BBB_BBB_BBB).
Auto Off Function
The tester is automatically powered off in about 10 minutes after
4 | 5 |