Milwaukee Heavy-Duty Sanders and Grinders manual

WARNING!

A Type 1 guard must be installed when using

aType 1 cut-off wheel to provide maximum protection for the operator if the wheel should break.

Installing and Removing Type 1 Guard Assembly and Adjusting Shoe (Fig. 12)

Fig. 12

Carriage bolt and wingnut

Guard

Guard screw

Adjusting shoe

Spindle

1.Unplug tool and place it upside down on a level surface. Remove any accessories from spindle.

2.Loosen the guard screw and slip the guard over the spindle.

Position the guard in the location which offers best control and guard protection. For operating zones that provide maximum protection for the operator, see Fig. 9. Tighten the guard screw securely.

3.To adjust the guard, unplug the tool, loosen the guard screw, rotate the guard to the desired position and retighten the guard screw.

4.To remove the adjusting shoe, loosen the wing nuts, slide the shoe over to the access holes and lift out. To install the adjusting shoe, insert the head of the carriage bolts into guard access holes and slide the shoe over to the far edge of slots. Adjust shoe to desired position and tighten wing nuts securely.

5.To remove the guard, unplug the tool, remove the accessories and reverse the procedure.

Using Type 1 Cut-Off Wheels (Fig. 13)

1.Firmly grasp rear handle and side handle before starting and while us- ing tool. Allow wheel to come to full speed before starting.

2.When using a cut-off wheel, hold tool as shown, using only the edge of the wheel (Fig. 13).

Fig. 13

3.Control pressure and surface contact between wheel and workpiece. Too much pressure slows cutting speed.

WARNING!

To reduce the risk of injury, never use a Type 1 cut-off wheel for surface grinding.

page 10

Image 10

Milwaukee Heavy-Duty Sanders and Grinders manual Type 1 guard must be installed when using, Using Type 1 Cut-Off Wheels Fig

Contents

Operators Manual Manuel DE Lutilisateur Manual DEL Operador Personal Safety General Safety RulesElectrical Safety Service Functional Description Specific Safety Rules Sanders and GrindersSpindle Grounding Extension Cords Tool Assembly Installing the Side Handle Locking the Trigger Fig Select Models Adjusting the Rear Handle Position Fig Select ModelsOperation Sanding Disc and Grinding Wheel Material Using Sanding Discs Installing Grinding Wheels Fig Using Grinding and CUT-OFF WheelsInspecting Wheels Selecting Wheels Type 1 guard must be installed when using Using Type 1 Cut-Off Wheels Fig Installing Wire Cup Brushes Fig Using Wire BrushesSelecting Wire Brushes Installing Wire Wheel Brushes Fig Warranty MaintenanceAccessories Repairs Utilisation ET Entretien DES Outils Conservez CES Instructions Aire DE TravailSécurité Électrique Sécurité DES Personnes Réparation Règles DE Sécurité Particulière Description Fonctionnelle Cordons DE Rallonge Calibres minimaux recommandés pour les Cordons de rallongeMise À LA Terre Avertissement Directives pour l’emploi des cordons de rallonge Montage DE Loutil Avertissement Pose de la poignée latérale Positionnement de la poignée Fig Certains Modèles Maniement AvertissementSélection des disques abrasifs et des meules Composants des disques abrasifs et des meules Utilisation DES Disques Abrasivs Choix des disques abrasifs et des grains Installation de la meule FigUtilisation DES Meules Abrasives ET DES Meules À Tronçonner Corindon Aluminium-Zircone Céramique Choix des meules Inspection des meulesMeulage et Utilisation des meules à tronçonner de type 27 Fig Utilisation des meule à tronçonner de type 1 Fig Sélection des brosses à fils d’acier Installation des brosses-boisseau à fils d’acier FigUtilisation DES Brosses À Fils Dacier Utilisation des brosses à fils d’acier Garantie Maintenance AvertissementAccessoires Réparations Seguridad Personal Guarde Estas Instrucciones Area DE TrabajoSeguridad Electrica USO Y Mantenimiento DE LA Herramienta Reglas Especificas DE Seguridad Lijadoras Y Esmeriladoras Simbología Especificaciones Descripcion Funcional Extensiónes Eléctricas Tierra ¡ADVERTENCIAGuías para el uso de cables de extensión Ensambaje DE LA Herramienta ¡ADVERTENCIA Instalación del mango lateral Material de discos abrasivos y ruedas abrasivas Operacion ¡ADVERTENCIABloqueo del gatillo Fig Modelos seleccionados Ajuste de la posición del mango Fig Modelos seleccionados USO DE Discos Abrasivos Selección de discos abrasivos y granos USO DE Ruedas Abrasivas Y Ruedas DE CorteInstalación de ruedas abrasivas Fig Revisión de las ruedas Solución de problemasSelección de ruedas Uso de las ruedas de corte tipo 1 Fig Instalación de cepillos de alambre acopados Fig Usando DE Cepillos DE AlambreSelección de cepillos de alambre Instalación de los cepillos de alambre tipo rueda Fig Garantia Mantenimiento ¡ADVERTENCIAAccesorios Reparaciones United States