Mitsubishi Electronics FX2N 2.2 Wiring

FX2N-32DP-IF Profibus-DP Interface Unit Wiring and Mounting Arrangements 2

2-2

2.2 Wiring

2.2.1 Caution for Wiring

1) Do not lay signal cable near to high voltage power cab le or house t hem in the same trunking

duct. Effects of noise or surge induction may occur. Keep signal cables a safe distance of

more than 100 mm (3.94") from these power cables.

2) Ground the shied wire or the shield of a shielded cable at one point on the programmable

controller. Do not, however, ground at the same point as high voltage lines.

3) The terminal screws of the 32DP-IF are M3.5 (0.14"), theref ore t he c rimp style terminal (see

drawing) suitable for use with these screws should be fitted to the cable for wiring.

Figure 2.3:Crimp Terminals

4) The terminal tightening torque is 0.5 to 0.8 N•m. Tighten securely to avoid malfunction.

5) Cut off all phases of power source before installation or performing wiring work in order to

avoid electric shock or damage of product.

6) Replace the provided terminal cover before supplying power and operating the unit after

installation or wiring work, in order to avoid electric shock.

6.8 mm (0.27" )

or less

For M3.5 (0.14") 6.8 mm (0.27")

or less

For M3.5 (0.14")

Contents

Main Page Page Page Page Page Page Page Table of Contents 2. Wiring and Mounting Arrangements ......................................................2-1 Page 1. Introduction 1.1 Features of the 32DP-IF 1.2 External Dimensions and Each Part Name Figure 1.1:External Dimensions COM 24 + LN Figure 1.2:Pin Layout 9-pin D-SUB Table 1.1: Pin Configuration 1.3 System Configuration Figure 1.3:System Configuration Caution Table 1.2: Table 1.3: Connected Extension Units/Blocks and Exchanged Data Length Page Figure 1.4:Number of Expansion I/O and 24 V DC Service Supply Capacity (mA) Table 1.6:24 and 5 V DC Supply Capacity Table 1.7:Power Supply for Special Function Blocks Figure 1.5:Example Configuration Table 1.8:Check 5 V DC Bus Supply A Series PLC A1SJ71PB92 (software version E) Table 1.9:Check Total I/O Points and the Loading on the 24 V DC Service Supply Table 1.10:Check Total Exchanged Data Length 2. Wiring and Mounting Arrangements 2.1 Mounting Arrangements Figure 2.2:Mounting Arrangement Figure 2.1:Mounting Location 2.2 Wiring Figure 2.3:Crimp Terminals Figure 2.4:Wiring about 32DP-IF and Profibus-DP Network Figure 2.5:Wiring for Power Line Circuit Figure 2.6:Profibus Connector Figure 2.7:Source (positive input connection, negative S/S) Figure 2.8:Sink (negative input connection, positive S/S) NPN PNP 3. Specifications 3.1 General Specifications 3.2 Power Supply Specifications Table 3.1:General Specifications Table 3.2:Power Supply Specifications 3.3 Performance Specificatio ns Table 3.3:Performance Specifications 4. Advanced Devices 4.1 Data Registers Table 4.1:Supported Data Register List Figure 4.1:Example of Allocating Device Table 4.2:Example of Allocating Device Page 4.2.1 32DP-IF Status (M8000 ~ M8009 and D8000 ~ D8009) Figure 4.2:Momentary Power failures Figure 4.3:32DP-IF Version dec Table 4.3:Special Auxiliary Relays (M8000 ~ M8009) (ref. D8007) Note 1: Swap byte order Table 4.5:Special Auxiliary Relays (M8020 ~ M8039) Table 4.6:Special Data Registers (D8020 ~ D8039) Note 2: Baud rate Table 4.7:Baud Rate in D8024 Note 3: Communication status Table 4.8: Communication Status in D8025 Note 4: Error status Table 4.9:Error status in D8029 Figure 4.4:Configuration Data Table 4.10:Special Data Registers (D8040 ~ D8059) bit 0 bit 7 4.2.4 Error Status (M8060 ~ M8069 and D8060 ~ D8069) Table 4.11:Special Auxi liary Relays (M8060 ~ M8069) Table 4.12:Special Data Registers (D8060 ~ D8069) Page 5. Address Setting 5.1 Setting Address Figure 5.1:Address Setting 5.2 Example Address Setting Page 6. User Parameter 6.1 User Parameter Rules Table 6.1:User Parameter Configuration Figure 6.1: User Parameter Rules Figure 6.2:Order BFM No. for adjusting BFMs Table 6.2:Type Code of Special Function Blocks BFM No. for adjusting Writing flag: Bit 7 = ON (1): Write to BFM Bit 7 = OFF (0): Not write to BFM bit 0 bit 7 6.2 Configuring Slave Parameter Caution: Caution: Figure 6.3:Process Making Parameter Data by Programming Tool 7. Diagnostic Message 7.1 Diagnostic Massage Frame 7.2 Diagnostic Message Contents List Figure 7.1: Diagnostic Massage Frame Table 7.1:Diagnostic Message List Page 8. Diagnostics 8.1 Preliminary Checks 8.2 Check the Status of the LEDs for the 32DP-IF 4) Check the status of the DIA LED 2) Check the status of the RUN LED 3) Check the status of the BF LED Table 8.1:POWER LED Check 8.3 Check Error Status of the 32DP-IF 8.3.1 Error Status in D8029 Table 8.5:Error Status in D8029 8.3.2 Error Flags Table 8.6:Error Flags 8.3.3 Error Code Page Appendix A: Default Parameter <After Power ON> A-1 User Parameter <After Power ON> *2 After power on, the default setting of this parameter for every special function block is 2. Figure A-1:User Parameter <After Power ON> Table A-1: Type Code of Special Function Blocks A-2 Exchanged Data by Default Parameter Example Table A-2: Exchanged Parameter Data Table A-3: Example Exchanged Parameter Data Appendix B: Example Setting User Parameters For user parameters, refer to chapter 6. B-1 Example Configuration User Parameters B-1-1 Example Setting for FX2N-4AD For BFMs definition, ref er to FX2N-4AD Users Manual. Table B-1:User Parameter FX Table B-2:User Parameter For FX -4DA B-1-3 Example Setting for FX2N-4AD-PT For BFMs definition, ref er to FX2N-4AD-PT Users Manual. Table B-3:User Parameter for FX -4AD-PT B-1-4 Example Setting for FX2N-4AD-TC For BFMs definition, ref er to FX2N-4AD-TC Users Manual. Table B-4:User Parameter for FX -4AD-TC B-2 Setting the Number of Average for Leveled Input Data Table B-5:Setting number of average for leveled input data of FX -4AD. B-3 Adjusting Offset and Gain Going to next step, must be delay times as follows. Figure B-1:Process for Adjusting Offset/Gain Table B-6:Delay Times 1) First step in adjusting offset/gain Table B-7:First Step in Adjusting Offset/Gain for FX 2) Second step in adjusting offset/gain a) Second step in adjusting offset/gain for FX2N-4AD Table B-8:Second Step in Adjusting Offset/Gain for FX FX2N-32DP-IF Profibus-DP Interface Units Appendix B B-9 b) Second step in adjusting offset/gain for FX2N-4DA Table B-9:Second Step in Adjusting Offset/Gain for FX 3) Last step for adjusting offset/gain Table B-10:Last Step for Adjusting Offset/Gain for FX B-4 Changing the High Speed Mode/Normal Mode Table B-11:Changing the High Speed Mode/Normal Mode for FX B-5 Returning to Default Settings Table B-12:First Step of Returning to Default Settings for FX 2) Step 2 of returning to default for FX2N-4AD Table B-13:Step 2 of Returning to Default Settings for FX Page Page USERS MANUAL FX2N-32DP-IF PROFIBUS-DP INTERFACE UNIT