Preparing your projector, Overview | Mitsubishi Electronics HC3900

Preparing your projector (continued)

Overview

10

3

1

2

4

8

5

9

6

1FOCUS ring

2ZOOM ring

3Control panel

4Air inlet grille

5Remote control sensor (Front)

6Air outlet grille

7Terminal board

8Adjustment feet

9Lock bar

10Lamp cover

Caution:

Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns.

7

Control panel

6

4

2

HC3900

7 8 9 5 3 1

1Power button

2POWER indicator

3MENU button

4STATUS indicator

5ENTER button

6AUTO POSITION / p button

7HDMI / COMPUTER / t button

8q button

9VIDEO/ u button

Important:

•While the menu or the screen for the keystone adjustment or password entry is being displayed, the HDMI / COMPUTER, VIDEO, and AUTO POSITION buttons function as the t, u, and p buttons respectively.

Terminal panel

5 6

1

2

3

4

1	VIDEO IN and S-VIDEO IN terminals
2	COMPONENT VIDEO IN terminals
3	COMPUTER IN/COMPONENT VIDEO IN terminal
	(Mini D-SUB 15-pin)
4	HDMI IN terminal (HDMI 19-pin)
5	SERIAL terminal (Mini DIN 8-pin)
	• Used for projector control by computer. Contact your
	dealer for details.
6	TRIGGER terminal
	• Used for the optional electric screen.
7	Power jack

7

EN-

Image 7

Mitsubishi Electronics HC3900 user manual Preparing your projector, Overview, Control panel, Terminal panel

Contents

HC3900 Risk of Electric Shock Do not Open When using the projector in Europe Contents Important safeguards Important safeguards What’s included in the box Inserting the batteries into the remote controlRemoving the batteries from the remote control Preparing your projector Terminal panel Preparing your projectorOverview Control panel Using the picture quality adjusting buttons Remote controlBottom side Operational range of the remote control Using the remote controlReception angle Screen size and projection distance Setting up your projectorSetting up the screen When the aspect ratio of the screen is When the aspect ratio of the screen is 2.351 CinemaScope Setting up your projectorWhen the aspect ratio of the image is To cancel the menu When fine streaks are seen on projected imagesWhen projected images are distorted to a trapezoid With the Installation menu See page 26 for menu setting Trigger terminal InstallationFront projection, ceiling mounting Rear projection Preparation Connecting the projector to video equipmentViewing video images Basic home theater system connection Viewing video images Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder When a TV tuner or VCR is connected Connection for video equipment having an Hdmi terminal Connecting to video equipment having a Hdmi terminal Plugging in the power cord Projecting images To stop projecting ZOOM1 ZOOM2 Stretch ANAMORPHIC1 ANAMORPHIC2 Setting the aspect ratio With the remote control How to change the settingsWith the Feature menu See page 26 for menu setting About DDC Connecting the projector to a computerPlugging the power cord Viewing computer images Computer Viewing computer images Auto Position button When connecting to a notebook computerSetting of the resolution Example of the setting procedure for external output Menu operation Keystone Lamp Mode Menu operation How to set the menusAvailable settings in the menus Setting Function Installation menu Feature menu User menu Signal menu Information menu To store the settingsTo enable the stored image quality settings AV memory How to Use BrilliantColorTM Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and Tint To enable the stored color temperature Adjusting projected imagesTo adjust the tone of white Color Temp About color temperature High How to Use Color ManagementTo adjust the ratio of change in brightness Gamma Mode Blue Magenta RED To adjust the vertical position To enable the stored gamma modeLPF Progressive filter To cancel the password function Advanced featuresPassword function To enable the password function Replacing the lamp Interval of lamp replacement Replacing the lamp When the projector is mounted to the ceilingTo replace the lamp Reset of the lamp operation time Cleaning of the projector and the ventilation slots MaintenanceCleaning of the lens No image appears on the screen Problem Solution Troubleshooting Images are not displayed correctly Problem Solution Troubleshooting Others Problem Solution EN-43 Abnormal condition IndicatorsStatus Condition Possible Solution Normal condition Dimension drawings unit mm Specifications Specifications VLT-HC3800LP ConnectorsReplacement part option/not included in the box Computer IN/COMPONENT Video Mitsubishi Electric Corporation