Mitsubishi Electronics XD500U-G, SD510U, XD500U-ST Password lock commands, How to set the value

6) Keystone commands (Not executable in stand-by mode. Possible only to read during muting.)

The keystone commands are used for the keystone setting of this projector with the value. The value will vary depending on the installation conditions, etc.)

ITEM	ASCII	HEX	VALUE
KEYSTONE(vertical)	KS	4Bh 53h	±20

How to set the value

Use the ASCII or HEX code as shown below to set the value.

ASCII

'+'

'–'

'0'

'1'

'2'

'3'

'4'

'5'

'6'

'7'

'8'

'9'

HEX

2Bh

2Dh

30h

31h

32h

33h

34h

35h

36h

37h

38h

39h

7) Mute commands (Not executable in stand-by mode. When the mute commands are sent while the splash screen is being displayed, the splash screen is only canceled.)

The mute commands are used for the mute setting of this projector with the 0 (30h) and 1 (31h).

ITEM

MUTE

ASCII	HEX	VALUE
MUTE	4Dh 55h 54h 45h	0 (OFF), 1 (ON)

8)Remote commands (Not executable in stand-by mode. When the remote commands are sent while the splash screen is being displayed, the splash screen is only canceled.)

Some remote control operations can be achieved by the remote command codes.The remote commands have no data codes.

Button's name on remote	ASCII	HEX
+ VOLUME	r06	72h	30h	36h
– VOLUME	r07	72h	30h	37h
KEYSTONE	r43	72h	34h	33h
MAGNIFY	r02	72h	30h	32h
AV MUTE	ra6	72h	61h	36h
▲	r53	72h	35h	33h
▼	r2b	72h	32h	62h
t	r4f	72h	34h	66h
s	r59	72h	35h	39h
MENU	r54	72h	35h	34h
ENTER	r10	72h	31h	30h
AUTO POSITION	r09	72h	30h	39h
FREEZE	ra4	72h	61h	34h
ASPECT	re2	72h	65h	32h

[Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands	Status code from	Description
from the PC, etc.	the projector
30 30 72 35 34 0D		Command operating the same
'0' '0' 'r' '5' '4' ' '		as the MENU button
	30 30 72 35 34 0D	Command receipt confirmation
	'0' '0' 'r' '5' '4' ' '	(Command echo back)

9) Password lock commands

The password lock commands control the password lock. The password lock enabling or disabling command is sent with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the password lock is enabled or disabled successfully, the projector sends a return command comprising the data code, password, and “1” at the end. When enabling or disabling the password lock fails, it sends a return command with “0” at the end. There is no reconfirmation of the password. The password input command is for enabling projection of image when password lock has been set to DISPLAY INPUT. The password input command is sent with a 4 to 8- digit password comprised of any figures 1 to 4 at the end.

ITEM	ASCII	HEX					VALUE
Password lock	PSLOCK	50h	53h	4Ch	4Fh	43h 4Bh	0**** (Disabling), 1**** (DISPLAY INPUT),
enabling/disabling							2**** (MENU ACCESS), 3**** (SPLASH ID SCREEN)
Password input	PASS	50h	41h	53h	53h		****

**** is a 4 to 8-digit password comprised of any figures 1 to 4.

3