Turning the power on and off
■Connecting the AC power cord
1 Insert the AC power cord connector into the AC IN socket of the projector.
2 Insert the AC power cord plug into a wall or other power outlet.
■ Turning the power off |
1 Press the ON/STANDBY button. |
A message appears on the screen, confirming that you wish to shut off the power. This |
message will disappear after a moment. (This operation is no longer valid after the |
(Supplied) AC Power cord connector
When the power cord is plugged in, the following three green indicators will come on for several seconds: POWER, TEMP, and LAMP. Next, the POWER indicator will change to orange, indicating standby mode.
(Do not perform any operations while the 3 green indicators are on.)
message disappears.) |
2 Press the ON/STANDBY button again. |
The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode.
When cooling lamp |
| During internal cooling |
| After cooling is completed |
|
|
|
|
|
FAN TEMP LAMP POWER |
| FAN TEMP LAMP POWER |
| FAN TEMP LAMP POWER |
Removing the lens cover
Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat.
(Green) | (Green) (Orange) | (Green) | (Off) | (Orange) | (Off) | (Off) | (Orange) | |||
|
| Flashing |
|
|
|
|
|
|
|
|
A |
|
| B |
|
|
| C |
|
|
|
A | During cooling, the LAMP indicator flashes. In this state, the power cannot be |
| turned back on. In addition, unplugging the power cord in this state will shorten |
| |
| the life of the lamp. |
| After the LAMP indicator goes off, the cooling fan continues to operate for a |
B | |
| short while in order to expel excess internal heat. |
■Turning the power on
Press the ON/STANDBY button.
The power turns on, and the following 3 green indicators light: POWER, LAMP, and FAN. After a moment, the
|
| Remote |
Control panel | Control | |
FAN TEMP LAMP POWER |
| |
SOURCE | ON / STANDBY |
|
| ZOOM. + |
|
| MENU/ENTER |
|
VOL. - | VOL. + |
|
KEYSTONE | AUTO POSITION |
|
| ZOOM. - |
|
C | In standby mode. |
|
Note
•The projector consumes about 6W of power in standby. We recommend you to unplug the AC power cord if you will not use the projector for an extended period.
PRECAUTIONS
• Before unplugging the AC power cord, make sure that the LAMP indicator is off. |
Unplugging the AC power cord and cutting off the power while the projector is running or |
being cooled will shorten the life of the lamp. However, please unplug the AC power |
cord if the projector locks up or acts abnormally. |
Operations
WARNING
• Do not look into the lens during operation. Doing so could damage your vision.
CAUTION
•Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
•Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object.
Notes
•The
•The first time you use the projector after purchase, after the
• If the AC power cord was unplugged before cooling was complete, give the lamp |
sufficient time to cool before plugging it back in. If the lamp overheats, it may fail to light, |
and its lifetime will be shortened. |
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the following precautions.
•In order to extend the lifetime of the LCD panel, always turn off the power when not in use, and make sure that the lamp is off. Keeping the lamp off is also very effective at saving electricity.
•If the air filter becomes dirty and clogged, the projector’s internal temperature will rise, shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter from time to time p.32 , and replace it periodically. Contact the store where you purchased your projector, or your local Service Station for replacement air filters.
20 | 21 |
