Mitsubishi Electronics WD-57833 manual Receiver Sound System, Older Cable Box

3. TV Connections 23

A/V Receiver (Sound System)
				Important
Most setups require either a digital audio cable or
			A/V Receivers with HDMI Inputs
analog stereo audio cables.			If your A/V receiver has an HDMI input, use
The TV makes all audio available in digital and analog			one of the audio connections described here
			instead of an HDMI connection.
formats:
		Analog audio coming into the TV is available as	Note:
		output in digital stereo format on the DIGITAL
		AUDIO OUT jack.		On rare occasions, an HDMI signal may be
		Digital incoming audio is available as analog		copy-restricted and cannot be output from
		output on the AVR AUDIO OUTPUT/AUDIO L		the TV as a digital signal. To hear these copy-
				protected signals through the A/V receiver, use
		(MONO) and AUDIO R jacks.
				connections for analog A/V receivers.
Usually, only one of the following connections is
				Check the A/V receiver’s Owner’s Guide for
required:
				information concerning use of the digital input
• To connect an analog A/V receiver
				and switching between digital sound and
	Connect left (white) and right (red) audio cables			analog stereo sound from the TV.
	from AVR AUDIO OUTPUT/AUDIO L (MONO) and
AUDIO R on the TV back panel to the TV AUDIO
	INPUT on the A/V receiver.

•To connect a digital A/V receiver with Dolby

	Digital surround sound and PCM audio support:				Older Cable Box
	Connect one end of the digital audio cable				Required: One coaxial cable.
	to DIGITAL AUDIO OUT on the back of the TV.
	Connect the other end to the COAXIAL DIGITAL				Note: This connection is not recommended. The
	INPUT on the back of the	A/V receiver.
					other connections described in this chapter
					provide better quality audio and video to the TV
					and allow NetCommand to work with the cable
	015*$"-				box.
	*/165				1. Connect the incoming cable to IN on cable box.
	$0"9*"-				2. Connect one coaxial cable from OUT on the cable
	*/165				box to ANT 1/MAIN onEMITTERthe TV back panel.				AUDIO-
								RECORD	LEFT
								OUTPUT
									AUDIO-
								VIDEO	RIGHT
	%JHJUBM $PBYJBM $BCMF							INPUT 1
	6TF UP DPOOFDU B				ANT 2 / AUX		IEEE 1394	INPUT 2
	EJHJUBM "7 SFDFJWFS				ANT 1 / MAIN	DIGITAL
						AUDIO	IR EMITTER	S-VIDEO	VIDEO
						RS-232C		1 (LEFT) , 2 (MIDDLE) , 3 (RIGHT)
						OUTPUT		HDMI
							NetCommand	VIDEO: 480i / 480p / 720p /
	4UFSFP "OBMPH $BCMFT							1080i / 1080p
								W-SVGA, XGA, W-XGA,
								AUDIO: LINEAR PCM
								PC: VGA, W-VGA, SVGA,
	6TF UP DPOOFDU BO BOBMPH							SXGA / 720p / 1080p
	"7 SFDFJWFS				5P "/5 ."*/		57 #BDL 1BOFM
	57 #BDL 1BOFM
		Y Pb Pr (480i/480p/720p/1080i)
		Y Pb	Pr	L (MONO)- AUDIO - R			065
		COMPONENT 1
		COMPONENT 2
	3D GLASSES
	EMITTER		AUDIO-	DVI / PC
			LEFT	AUDIO
		RECORD		INPUT
		OUTPUT	RIGHT	AUDIO		*ODPNJOH	*/
		VIDEO
			AUDIO-	AVR
				OUTPUT		$BCMF
		INPUT 1					$BCMF #PY
	IEEE 1394	INPUT 2
ANT 2 / AUX	DIGITAL
ANT 1 / MAIN	AUDIO	S-VIDEO	VIDEO	L (MONO)- AUDIO - R
	OUTPUT	HDMI
	RS-232C IR EMITTER	1 (LEFT) , 2 (MIDDLE) , 3 (RIGHT)
	NetCommand	VIDEO: 480i / 480p / 720p /
		1080i / 1080p			Figure 12. Connecting an older cable box
		W-SVGA, XGA, W-XGA,
		AUDIO: LINEAR PCM

PC: VGA, W-VGA, SVGA,

SXGA / 720p / 1080p

Figure 11. Connecting the TV to an A/V receiver