Manuals / Brands / Computer Equipment / Projector / Mitsubishi Electronics / Computer Equipment / Projector

Mitsubishi Electronics WD620U, WD620U-G, XD600U, XD600U-G user manual Overview

1 44

Download 44 pages, 3.31 Mb

EN-6

Overview

1FOCUS ring

2ZOOM ring

3 Control panel

4 Air inlet grille

5 Remote control sensor (Front)

6 Air outlet grille

7 Terminal board

8 Speaker

9 Adjustment feet

10 Lock bar

11 Lamp cover

Caution:

Do not replace the lamp immediately after using the pro-

jector because the lamp would be extremely hot and it

may cause burns.

Control panel

1 Power button

2 POWER indicator

3 MENU button

4 STATUS indicator

5 KEYSTONE/ENTER button

6 AUTO POSITION / S button

7 COMPUTER / W button

8T button

9 VIDEO/ X button

Important:

• While the menu or the screen for the keystone adjust-

ment or password entry is being displayed, the COM-

PUTER, VIDEO, and AUTO POSITION buttons

function as the W, X, and S buttons respectively.

• While the menu is on the screen, the KEYSTONE but-

ton functions as the ENTER button.

Terminal board

1Power jack

2 COMPUTER IN terminal (1, 2) (Mini D-SUB 15-pin)

3 MONITOR OUT terminal (Mini D-SUB 15-pin)

4 Remote control sensor (Rear)

5 AUDIO IN-1 terminal (Mini jack)

6 AUDIO IN-2 terminal (Mini jack)

7 AUDIO OUT terminal (Mini jack)

8 S-VIDEO terminal

9 VIDEO terminal

10 SERIAL (RS-232C) terminal (Mini DIN)

11 Kensington Lock

12 LAN terminal (RJ-45)

13 AUDIO IN-3 terminals (L/R)

14 HDMI terminal (HDMI 19-pin)

Kensington Lock

This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System.

Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington

Technology Group below.

Kensington Technology Group

2855 Campus Drive

San Mateo, CA 94403, U.S.A.

Phone: +1- (650)572-2700 Fax: +1- (650)572-9675

11

985

123 4

10

7

6

642

895317

75138214 3 1012 4

619 11

Contents

Main WARNING DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION When using the projector in Europe: COMPLIANCE NOTICE CAUTION CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, Contents Important safeguards WARNING: Overview Control panel 619 11 Terminal board Kensington Lock Overview (continued) Bottom side Remote control Remote control Battery installation Reception angle (vertical) Operation range (of the remote control) Reception angle (horizontal) Reception angle (vertical), ceiling mount Installation Layout of the projector XD600U/XD600U-G The above figures are approximate and may be slightly different from the actual measurements. Image size varies depending on the distance between the screen and the projector. Front projection Installation (continued) When the aspect ratio of the screen is 4:3 When the aspect ratio of the image is 16:10 (WXGA) When the aspect ratio of the image is 16:9 Front projection, ceiling mounting Installation (continued) Rear projection Basic connections Projector + AV device Projector + DVD player or HDTV decoder Basic connections (continued) Connection (for video equipment having an HDMI terminal) Basic connections (continued) Projector + Computer For computer with Mini D-SUB For analog connection: For monitor connection: Preparation Preparation for projection Warning: Caution: Adjustment of the projection angle Basic operation Power-on Important: When fine streaks are seen on projected images 4 6 Basic operation (continued) Power-of f 1. 2. 3. Basic operation (continued) Wall Screen When connecting to a laptop computer: Menu operation QUICK MENU QUICK MENU QUICK MENU Basic operation QUICK MENU Menu Options Set the following options provided in the respective menus. 2.INFORMATION menu 1.QUICK MENU DETAIL MENU * Menus are not displayed when no signal is supplied to the projector. LOW CONTRAST Basic operation Important: IMAGE ADVANCED menu INSTALLATION Menu Options 2.INSTALLATION menu INSTALLATION ADVANCED menu 3.FEATURE menu 4.SINGAL menu SIGNAL USER menu 5.NETWORK menu You can set the IMAGE, SIGNAL, and SIGNAL-USER menus only when the signal is input. NETWORK IP CONFIG menu 6.INFORMATION menu Image adjustment Adjusting projected images To adjust the brightness (CONTRAST and BRIGHT- NESS): CONTRAST BRIGHTNESS Image adjustment (continued) BrilliantColor RGB-COLOR RGB-TINT How to adjust the image supplied from the computer using the menu: Network settings Setting Projector Name Network Password Settings IP Settings Network settings (continued) Setting or Clearing DHCP IP Address Settings Subnet Mask Settings Default Gateway Settings Network settings (continued) How to Use Network Function Glossary Advanced features Displaying a user-defined image during startup or mut- ing Procedure Freeze To stop the motion in the image temporarily (or to dis- play a still image): Advanced features (continued) To cancel the password function: Magnify To use the MAGNIFY mode: Advanced features (continued) Supervising and controlling by computer Major functions Connection Using the User Manual Lamp replacement A) When the projector is placed on the table B) When the projector is mounted to the ceiling Lamp replacement (continued) Reset of the lamp operation time Interval of lamp replacement Caution: Troubleshooting Unplug the power cord from the wall outlet and contact your dealer. No image appears on the screen. J Troubleshooting (continued) Images are not displayed correctly. Troubleshooting (continued) Others If the following problem occurs after the lamp is replaced, check the following first. Maintenance Warning: Indicators Abnormal condition Normal condition Specifications Specifications (continued) Connectors Replacement part Dimensional drawings (unit : mm) Whats included in the box Specifications (continued) Specification of RGB signals in each computer mode of the projector Mitsubishi Projector Warranty, Sales Support and Service Information MITSUBISHI ELECTRIC CORPORATION Ver.1 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan