When an Indicator is Lit or Blinking
The indicators on the projector’s control panel light or flash to notify of problems, as described below.
An indicator is also used to notify you of the currently set power mode. See “Power Cable Connections and Switching the Power On/Off” on page
STATUS indicator |
| STATUS |
|
|
|
| |
MENU |
|
| STANDBY |
| DUAL | COLOR |
|
|
|
| |
| MODE | SOURCE | |
|
|
| |
STANDBY indicator | AUTO | ||
|
|
| |
|
| Indicator status | What you should do | |
|
|
|
| |
STATUS | STANDBY | When the power is on (Lit green) | It is time to replace the lamp. | |
Standby (Lit amber) | Replace with a new lamp cartridge. | |||
|
| |||
|
| Lit red |
| |
|
|
|
| |
|
|
| The lamp has reached the end of its service life. The power | |
STATUS | STANDBY | Blinks amber for 60 seconds, then lit | will no longer turn on. | |
|
| The projector can be used for 100 hours after the lamp has reached | ||
|
| amber | ||
|
| the end of its service life. | ||
|
|
| ||
|
| Lit red | Replace with a new lamp cartridge. | |
|
|
| ||
|
|
|
| |
STATUS | STANDBY | Lit red | The lamp cover is open. | |
|
| Blinks red | The lamp cover is not properly mounted. Mount it properly. | |
|
|
| ||
|
| (lit for 1 seconds/off for 1 seconds) |
| |
|
|
|
| |
|
|
| The temperature is abnormally high. | |
|
|
| • The temperature protector has been activated. If the room tem- | |
STATUS | STANDBY | Lit red | perature is high, move the projector to a cool place. If the | |
|
|
| projector’s internal temperature is high, check the cooling fan’s | |
|
| Blinks red | ventilation slots and clean them if they are clogged. | |
|
| (lit for 0.5 seconds/off for 0.5 seconds) | • When the temperature protector is activated, the power turns | |
|
|
| off and in some cases will not turn back on immediately. In this | |
|
|
| case wait about 90 seconds, then try again. | |
|
|
|
| |
STATUS | STANDBY | Lit amber | The fan has stopped. | |
|
| Unplug the power cable and contact a store that sells the XD80U | ||
|
| Blinks red | ||
|
| for repairs. | ||
|
| (lit for 0.5 seconds/off for 0.5 seconds) |
| |
|
|
|
| |
STATUS | STANDBY | When the lamp has burned out dur- | The lamp will not light. | |
|
| ing use | Wait at least 90 seconds, then turn the power back on. If the prob- | |
|
| Blinks amber for 90 seconds, then lit | lem persists, unplug the power cable and contact a store that sells | |
|
| amber | the XD80U for repairs. | |
|
| When the lamp does not come on |
| |
|
| from the start |
| |
|
| Lit amber |
|
Blinks red
(lit for 1 seconds/off for 1 seconds)
Should an indicator be in a condition other than normal or flash at a rate other than the aforementioned, disconnect the power cable and contact your store of purchase.
Thermal Protector
When the temperature inside the projector becomes abnormally high, the STATUS indicator flashes red (0.5 seconds on/0.5 seconds off), the STANDBY indicator is a steady red, and at the same time the temperature protector operates and switches off the power of the projector.
Should this happen, please take the following actions.
1.Switch off the power and disconnect the power plug from the wall outlet.
2.Check the following matters and take the required measures.
When the projector is being used in a location that has a high ambient temperature, set it up again in a cool location. Check the outflow and intake holes and clean them if they are obstructed.
3.Wait about 60 minutes until the temperature of the projector drops.
If after having performed the above matters, the problem still has not been solved, please contact your store of purchase.
