Mitsumi electronic MELSEC FX1S LVD

FX1S Series Programmable Controllers

LVD

The following products have shown compliance through direct testing (of the identified

standards below) and design analysis (through the creation of a technical construction file) to

the European Directive for Low Voltage (73/23/EEC) when used as directed by the appropriate

documentation.

Refer to a manual or related material of each product for details concerning products not

included below.

Type : Programmable Controller (Open Type Equipment)

Models : MELSEC FX1S series manufactured

from March 1st, 2000 FX1S-MR-ES/UL

from September 1st, 2000 FX1S-MR-DS

from July 1st, 2001 FX1S-MT-ESS/UL

Where  indicates:10,14,20,30

Standard Remark

EN61010-1:2001 Safety requirements for electrical

equipment for measurement,

control,and laboratory use

- General requirements

The equipment has been assessed as

a component for fitting in a suitable enclosure

which meets the requirements of

EN61010-1:2001

Contents

Main FX1S Series Programmable Controllers Foreword FX1S Series Programmable Controllers Hardware Manual Guidelines for the Safety of the User and Protection of the FX1S. Page Page Marine standard Note Concerning the CE Marking EMC Models : MELSEC FX2NC series manufactured from October 1st, 2002 FX2NC-232ADP FX2NC-485ADP LVD Page Page Page Table of Contents Page Page Page Page Page 1-1 1. Introduction (2.96) Table 1.1:AC Power, Relay Output Units 0.30 (0.66) 0.40 (0.88) Table 1.3:DC Power, Relay Output Units +10%, -15% Table 1.4:DC Power, Transistor Output Units +10%, -15% 1-3 Figure 1.1: FX1S Outline Drawing Dimensions: mm (inches) W W-8(0.32") ES/UL,ESS/UL:75(2.96") DS,DSS :49(1.93") 82(3.23") 90(3.55") 2-4.5 (0.17") *1 The communication adapter needs to connect via an FX1N-CNV-BD to the FX1S Series PLC. Table 1.5: Expansion Board and Communication Adapter Page 1.2 World Specification Table 1.7: World / Japanese Specifications Page 1-8 1.4 Configuration Figure 1.2: Schematic System Page Table 1.9: Configuration Notes Table 1.10: Connection Ports Note Caution 1.5 Backup Data 2-1 2. Terminal Layouts -14MR-ES/UL -10MR-ES/UL -30MR-ES/UL -20MR-ES/UL 2.2 FX1S-**MR-DS Figure 2.2: Terminal Layouts, Relay Outputs, DC Power -30MR-DS -20MR-DS -10MR-DS 2.3 FX1S-**MT-DSS Figure 2.3: Terminal Layouts, Transistor Outputs, DC Power -30MT-DSS -20MT-DSS -10MT-DSS 2.4 FX1S-**MT-ESS/UL Figure 2.4: Terminal Layouts, Transistor Outputs, AC Power -20MT-ESS/UL -10MT-ESS/UL -30MT-ESS/UL Page 3-2 3.1 Product Outline -14MR Figure 3.1: Features of the FX1S PLC Table 3.1: Feature Table FX Page 3-4 3.3 General Specifications Table 3.3: General Specifications Page Page Page 3-8 3.5 DIN Rail Mounting = 4.5 mm (0.17") 3.6 Direct Mounting Table 3.4: Hole positions UNIT mm inches 0.2 0.01 A = W-8mm (0.32") FX1S-10M = 4.5 mm (0.17") Table 3.5: Hole positions 3.7 Termination of Screw Terminals Page Page Page Page Page Page Page 4.3 Power Supply 4.4 Power Supply Characteristics *1 Includes the input current (5 or 7mA per point). Table 4.1: AC Input Power Requirements, FX Page Page Page Page Page Page Page Page Page Page Page Page Bad Good Page Page Page Page Page 7.2 ERROR LED ON (CPU ERROR) Table 7.2: Error LED Checks 99 8 Page 7.5 Operation and Error Flags Table 7.3: Operation and Error Flags Page 7.7 Error Registers Table 7.5: Error Registers Page 7.9 Instruction List Table 7.7: Numerically Sorted Table 7.8: Alphabetically sorted Page Page Page Page Page Page Page Page Page Page HARDWARE MANUAL