Mitsumi electronic MELSEC FX1S Note, Caution

FX1S Series Programmable Controllers Introduction 1

1-11

1

2

3

4

5

6

7

8

Note

When connecting peripheral equipment (programming tool or GOT [direct connection to

CPU]) via the FX1N-232-BD, FX1N-422-BD, FX2NC-232ADP or the FX0N-232ADP, FX1S main

unit should be the following setting condition.

- Set the special data register for the communication format setting of the channel

connecting the peripheral equipment (D8120) to K0.

- Set the communication parameter to "Not set".

1.4.1 Note for Using Expansion Board

The following conditions cannot be accomplished with an FX1S PLC.

-FX

1N-422-BD + FX-2PIF

-FX

1N-5DM + FX1N-422-BD + FX-10DM-E

-FX-10DM-E + FX

1N-422-BD + FX-10DM-E

- Connect two Programming tools (FX-10P-E, FX-20P-E, FX-30P, Programming software,

etc.)

- The use of Special function Blocks

Caution

Connect a programming tool (such as an FX-10P-E, FX-20P-E, FX-20P-E-SET0, FX-30P

and personal computer) to either the connector built in to the PLC or the connector on the

FX1N-422-BD or FX1N-232-BD. If a programming tool is connected to both connectors, the

program stored in the PLC may not match the program stored in the programming tool. If

the program is changed or the set value of timers or counters are changed with this configu-

ration, the program may be partially overwritten and the PLC may malfunction.

Contents

Main FX1S Series Programmable Controllers Foreword FX1S Series Programmable Controllers Hardware Manual Guidelines for the Safety of the User and Protection of the FX1S. Page Page Marine standard Note Concerning the CE Marking EMC Models : MELSEC FX2NC series manufactured from October 1st, 2002 FX2NC-232ADP FX2NC-485ADP LVD Page Page Page Table of Contents Page Page Page Page Page 1-1 1. Introduction (2.96) Table 1.1:AC Power, Relay Output Units 0.30 (0.66) 0.40 (0.88) Table 1.3:DC Power, Relay Output Units +10%, -15% Table 1.4:DC Power, Transistor Output Units +10%, -15% 1-3 Figure 1.1: FX1S Outline Drawing Dimensions: mm (inches) W W-8(0.32") ES/UL,ESS/UL:75(2.96") DS,DSS :49(1.93") 82(3.23") 90(3.55") 2-4.5 (0.17") *1 The communication adapter needs to connect via an FX1N-CNV-BD to the FX1S Series PLC. Table 1.5: Expansion Board and Communication Adapter Page 1.2 World Specification Table 1.7: World / Japanese Specifications Page 1-8 1.4 Configuration Figure 1.2: Schematic System Page Table 1.9: Configuration Notes Table 1.10: Connection Ports Note Caution 1.5 Backup Data 2-1 2. Terminal Layouts -14MR-ES/UL -10MR-ES/UL -30MR-ES/UL -20MR-ES/UL 2.2 FX1S-**MR-DS Figure 2.2: Terminal Layouts, Relay Outputs, DC Power -30MR-DS -20MR-DS -10MR-DS 2.3 FX1S-**MT-DSS Figure 2.3: Terminal Layouts, Transistor Outputs, DC Power -30MT-DSS -20MT-DSS -10MT-DSS 2.4 FX1S-**MT-ESS/UL Figure 2.4: Terminal Layouts, Transistor Outputs, AC Power -20MT-ESS/UL -10MT-ESS/UL -30MT-ESS/UL Page 3-2 3.1 Product Outline -14MR Figure 3.1: Features of the FX1S PLC Table 3.1: Feature Table FX Page 3-4 3.3 General Specifications Table 3.3: General Specifications Page Page Page 3-8 3.5 DIN Rail Mounting = 4.5 mm (0.17") 3.6 Direct Mounting Table 3.4: Hole positions UNIT mm inches 0.2 0.01 A = W-8mm (0.32") FX1S-10M = 4.5 mm (0.17") Table 3.5: Hole positions 3.7 Termination of Screw Terminals Page Page Page Page Page Page Page 4.3 Power Supply 4.4 Power Supply Characteristics *1 Includes the input current (5 or 7mA per point). Table 4.1: AC Input Power Requirements, FX Page Page Page Page Page Page Page Page Page Page Page Page Bad Good Page Page Page Page Page 7.2 ERROR LED ON (CPU ERROR) Table 7.2: Error LED Checks 99 8 Page 7.5 Operation and Error Flags Table 7.3: Operation and Error Flags Page 7.7 Error Registers Table 7.5: Error Registers Page 7.9 Instruction List Table 7.7: Numerically Sorted Table 7.8: Alphabetically sorted Page Page Page Page Page Page Page Page Page Page HARDWARE MANUAL