Mitsumi electronic MELSEC FX1S 3.7 Termination of Screw Terminals

FX1S Series Programmable Controllers Installation Notes 3

3-10

3.7 Termination of Screw Terminals

Terminal screws should be tightened to between 0.5 to 0.8 Nm. Terminal screws must be

secured to prevent a loose connection thus avoiding a malfunction. Failure to do so may cause

equipment failures or malfunctions.

The terminal screws for the FX1S Series PLC are M3.0. The crimp style ter minal (see Figure

3.4 and 3.6) is suitable for use with these screws and should be fitted to the cable for wiring.

When installing 1 or 2 crimp terminals to a terminal, see explanation Figure 3.5 and 3.7.

However, 3 crimp terminals or more should not be installed to a single terminal.

Contents

Main FX1S Series Programmable Controllers Foreword FX1S Series Programmable Controllers Hardware Manual Guidelines for the Safety of the User and Protection of the FX1S. Page Page Marine standard Note Concerning the CE Marking EMC Models : MELSEC FX2NC series manufactured from October 1st, 2002 FX2NC-232ADP FX2NC-485ADP LVD Page Page Page Table of Contents Page Page Page Page Page 1-1 1. Introduction (2.96) Table 1.1:AC Power, Relay Output Units 0.30 (0.66) 0.40 (0.88) Table 1.3:DC Power, Relay Output Units +10%, -15% Table 1.4:DC Power, Transistor Output Units +10%, -15% 1-3 Figure 1.1: FX1S Outline Drawing Dimensions: mm (inches) W W-8(0.32") ES/UL,ESS/UL:75(2.96") DS,DSS :49(1.93") 82(3.23") 90(3.55") 2-4.5 (0.17") *1 The communication adapter needs to connect via an FX1N-CNV-BD to the FX1S Series PLC. Table 1.5: Expansion Board and Communication Adapter Page 1.2 World Specification Table 1.7: World / Japanese Specifications Page 1-8 1.4 Configuration Figure 1.2: Schematic System Page Table 1.9: Configuration Notes Table 1.10: Connection Ports Note Caution 1.5 Backup Data 2-1 2. Terminal Layouts -14MR-ES/UL -10MR-ES/UL -30MR-ES/UL -20MR-ES/UL 2.2 FX1S-**MR-DS Figure 2.2: Terminal Layouts, Relay Outputs, DC Power -30MR-DS -20MR-DS -10MR-DS 2.3 FX1S-**MT-DSS Figure 2.3: Terminal Layouts, Transistor Outputs, DC Power -30MT-DSS -20MT-DSS -10MT-DSS 2.4 FX1S-**MT-ESS/UL Figure 2.4: Terminal Layouts, Transistor Outputs, AC Power -20MT-ESS/UL -10MT-ESS/UL -30MT-ESS/UL Page 3-2 3.1 Product Outline -14MR Figure 3.1: Features of the FX1S PLC Table 3.1: Feature Table FX Page 3-4 3.3 General Specifications Table 3.3: General Specifications Page Page Page 3-8 3.5 DIN Rail Mounting = 4.5 mm (0.17") 3.6 Direct Mounting Table 3.4: Hole positions UNIT mm inches 0.2 0.01 A = W-8mm (0.32") FX1S-10M = 4.5 mm (0.17") Table 3.5: Hole positions 3.7 Termination of Screw Terminals Page Page Page Page Page Page Page 4.3 Power Supply 4.4 Power Supply Characteristics *1 Includes the input current (5 or 7mA per point). Table 4.1: AC Input Power Requirements, FX Page Page Page Page Page Page Page Page Page Page Page Page Bad Good Page Page Page Page Page 7.2 ERROR LED ON (CPU ERROR) Table 7.2: Error LED Checks 99 8 Page 7.5 Operation and Error Flags Table 7.3: Operation and Error Flags Page 7.7 Error Registers Table 7.5: Error Registers Page 7.9 Instruction List Table 7.7: Numerically Sorted Table 7.8: Alphabetically sorted Page Page Page Page Page Page Page Page Page Page HARDWARE MANUAL