Monster Cable HTPS 7000 MKII manual

HOOK-UP GUIDE

C)Set the Outlet Pair to SWITCHED ON AFTER DELAY: Press MENU until the display shows the status of the Analog outlet pair. Press the SELECT button until the time delay changes to the required delay in seconds before the outlet pair will turn on after the ON/OFF button is pressed, as in Figure 3.

When the PowerSource is SWITCHED ON by pressing the front panel ON/OFF button, or by an external trigger signal, the outlet pair will go “live” after the time delay set as described above — 20 seconds in this case. The outlet pair with the maximum time delay setting will still turn off immediately when the ON/OFF button is pressed,

or when triggered by an external signal.

D)Set the Outlet Pair to UNSWITCHED (Always On): Press the MENU button until the display shows the status of the Analog outlet pair. Press the SELECT button until you see the display in Figure 4.

Once UNSWITCHED is selected, any component plugged into those outlets will receive power continuously as long as your PowerSource is plugged into a 120 volt outlet that is on.

NOTE: The unit is shipped with all outlet pairs set to SWITCHED ON.

15

Image 20

Monster Cable HTPS 7000 MKII owner manual Or when triggered by an external signal

Contents

Signature Htps 7000 Mkii Table of Contents Important Safety Information Page Proper Grounding and Installation Important Note Proper Power and Protection Dear Enthusiast Noel Lee Head Monster MONSTER’S Exclusive T2 Technology Or above 132Vrms MONSTER’S Patented Clean Power Stages Minds Behind the Monster Powersource Design Monster Signature Htps 7000 Mkii Powersource Features 3IGNATURE /*-ÇäääÊ Rear Signature Htps 7000 Mkii Powersource Features Page Digital Outlets HOOK-UP GuideDigital Outlet Hook-Up Video Outlet Hook-Up Video Outlets Use a corresponding outlet for best performance Analog Audio Outlet Hook-UpAnalog Audio Outlets Ultra-High Current Audio Outlet Hook-Up High Current Audio Outlets Outlet Programming Or when triggered by an external signal Over-Voltage and Under-Voltage Audible Alarm Setting Over-Voltage and Under-Voltage Automatic Shutdown Setting Coaxial Connections Hook-Up Phone/Network Connections Hook-Up Protect Phone/Network Line Connections as Follows Remote DC In Control Hook-Up Remote AC In Control Hook-Up Remote DC Out Control Hook-Up To Control Components Troubleshooting Symptom Possible Cause Remedy Turn the PowerSource On Unswitched outletTurn the component power On Grounded, attach a copper wire Unswitched LED Switched LED is OffPlug the plug into the component You wish to use to activate Indicator on front Same as Switched and haven’t plugged Timed OnPanel is Off Is emitting a loud Signature Htps 7000 Mkii Powersource Page Page Manual de l’utilisateur Table DES Matières Importantes Informations DE Sécurité Mise EN Garde Sources d’alimentationMise EN Garde Mise à la terre et polarisation Mise EN Garde Liquides Éviter les chocs électriques Mise EN Garde Sécurité du cordon d’alimentation Mise EN Garde Précautions en cas d’orage Remarque importante Protection et alimentation adéquates Mise À LA Terre ET Installation AdéquatesMise EN Garde Mise à la terre adéquate Cher passionné Direction de Monster Technologie T2 Exclusive À Monster Étages Brevetés Clean Power DE Monster LES Cerveaux Derrière LE Concept Powersource DE Monster VUE Avant VUE Spécifications DU Powersource Signature Htps 7000 Mkii De vos appareils Prises Numériques Guide DE RaccordementRaccordement aux prises numériques Raccordement aux prises vidéo Prises Vidéo Raccordement aux prises audio analogique Prises Audio Analogiques Raccordement aux prises audio de puissance Prises Audio de Puissance Programmation de sortie Guide DE Raccordement Réglage de l’alarme sonore de surtension et de sous-tension Guide DE Raccordement Raccordement aux connexions coaxiales Raccordement aux connexions téléphonique/réseau Protégez les connexions téléphonique/réseau comme suit Programmées s’allument après le délai imparti Vers les appareils de contrôle Dépannage PowerSource est allumé Les haut-parleurs Un appareil branchéAllumez l’appareil Émettent un La DEL de la prise non Commutée est éteinteCommutées est éteinte Des prises à distance sans avoir Distance est trop faible PowerSource dans l’appareil Le PowerSourceVotre installation Branchez la prise électrique du 15A/1800W Phase-Neutre P-N Phase-Terre P-T Neutre-Terre N-T30V c.c 12V c.c mA