Remote DC In Control Hook-Up | Monster Cable HTPS 7000 MKII manual

HOOK-UP GUIDE

Remote “DC In” Control Hook-Up

This feature connects your PowerSource to an automated Home Theater control system or allows another component with a Remote “DC Out” connection to automatically turn on and off your PowerSource.

A)Plug the AC power cable of the component you are using to control the PowerSource into

an unswitched outlet on the PowerSource. Note: This component must deliver a control voltage between 3-30 volts DC.

B)Plug one end of the 1/8" miniplug (supplied) into the corresponding Remote “DC In” connection on the PowerSource.

C)Plug the other end of the 1/8" miniplug into the Remote “DC Out” connection on the component that you want to turn on and off the PowerSource’s Switched Outlets when it is turned on.

Remote “AC In” Control Hook-Up

This feature connects your PowerSource to an automated Home Theater control system or allows another component with an AC outlet connection (for example, an AV receiver or preamplifier for example) to automatically turn on and off your PowerSource.

A)Insert the Remote “AC IN” Control cord’s female plug into the “AC IN” 120V connection.

B)Insert the Remote “AC IN” Control cord’s 2-prong male plug into a switched AC power outlet on the component (AV receiver or preamplifier). When this device is turned on, the outlets programmed as “Switched On” on the PowerSource will turn on immediately. The outlets programmed as “Switched On After Delay” will turn on after the set time delay.

20

Ê ÎHÎä6

Ê ££ä6

Image 25

Monster Cable HTPS 7000 MKII owner manual Remote DC In Control Hook-Up, Remote AC In Control Hook-Up

Contents

Signature Htps 7000 Mkii Table of Contents Important Safety Information Page Important Note Proper Power and Protection Proper Grounding and Installation Noel Lee Dear Enthusiast Head Monster Or above 132Vrms MONSTER’S Exclusive T2 Technology MONSTER’S Patented Clean Power Stages Minds Behind the Monster Powersource Design 3IGNATURE /*-ÇäääÊ Monster Signature Htps 7000 Mkii Powersource Features Rear Signature Htps 7000 Mkii Powersource Features Page Digital Outlet Hook-Up HOOK-UP GuideDigital Outlets Video Outlets Video Outlet Hook-Up Analog Audio Outlets Analog Audio Outlet Hook-UpUse a corresponding outlet for best performance High Current Audio Outlets Ultra-High Current Audio Outlet Hook-Up Outlet Programming Or when triggered by an external signal Over-Voltage and Under-Voltage Audible Alarm Setting Over-Voltage and Under-Voltage Automatic Shutdown Setting Coaxial Connections Hook-Up Protect Phone/Network Line Connections as Follows Phone/Network Connections Hook-Up Remote AC In Control Hook-Up Remote DC In Control Hook-Up To Control Components Remote DC Out Control Hook-Up Symptom Possible Cause Remedy Troubleshooting Unswitched outlet Turn the PowerSource OnTurn the component power On Grounded, attach a copper wire Switched LED is Off Unswitched LEDPlug the plug into the component You wish to use to activate Timed On Indicator on front Same as Switched and haven’t pluggedPanel is Off Is emitting a loud Signature Htps 7000 Mkii Powersource Page Page Manual de l’utilisateur Table DES Matières Mise EN Garde Sources d’alimentation Importantes Informations DE SécuritéMise EN Garde Mise à la terre et polarisation Mise EN Garde Liquides Éviter les chocs électriques Mise EN Garde Précautions en cas d’orage Mise EN Garde Sécurité du cordon d’alimentation Mise EN Garde Mise à la terre adéquate Mise À LA Terre ET Installation AdéquatesRemarque importante Protection et alimentation adéquates Cher passionné Direction de Monster Technologie T2 Exclusive À Monster Étages Brevetés Clean Power DE Monster LES Cerveaux Derrière LE Concept Powersource DE Monster VUE Avant VUE Spécifications DU Powersource Signature Htps 7000 Mkii De vos appareils Raccordement aux prises numériques Guide DE RaccordementPrises Numériques Prises Vidéo Raccordement aux prises vidéo Prises Audio Analogiques Raccordement aux prises audio analogique Prises Audio de Puissance Raccordement aux prises audio de puissance Programmation de sortie Guide DE Raccordement Réglage de l’alarme sonore de surtension et de sous-tension Guide DE Raccordement Raccordement aux connexions coaxiales Protégez les connexions téléphonique/réseau comme suit Raccordement aux connexions téléphonique/réseau Programmées s’allument après le délai imparti Vers les appareils de contrôle Dépannage Un appareil branché PowerSource est allumé Les haut-parleursAllumez l’appareil Émettent un Commutée est éteinte La DEL de la prise nonCommutées est éteinte Des prises à distance sans avoir Distance est trop faible Le PowerSource PowerSource dans l’appareilVotre installation Branchez la prise électrique du Phase-Terre P-T Neutre-Terre N-T 15A/1800W Phase-Neutre P-N30V c.c 12V c.c mA