Monte Carlo Fan Company 5STR52 owner manual Phillips Screwdriver, Pliers, Step Ladder, Safety Tips

TOOLS REQUIRED Wire Cutters

1.

2.

3.

4.

SAFETY TIPS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes an 70-1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con- ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

5. Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

7. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blade.

8. To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support. (Mounting must support at least 35 lbs.)

9. Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

10. Attach the mounting bracket using only the hardware supplied with the outlet box.

11. To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

12. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

13. NEVER place a switch where it can be reached from a tub or shower.

14. The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

15. Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

	Phillips Screwdriver		Pliers
1		2

Before you begin installing the fan, Switch power off			Before installing this fan	make sure the outlet
at Service panel and lock service disconnecting means		box is properly installed to the house structure.
to prevent power from being switched on accidentally.		To reduce the risk of fire, electric shock, or per-
When the service disconnecting means cannot be		sonal injury, mount to outlet box or supporting
locked, securely fasten a prominent warning device,		system acceptable for fan support.
such as a tag, to the service panel.		(Mounting must support at least 35 lbs.)
	5
4

Remote Transmitter Dip swtiches
Remote Receiver Dip switches
Set dip switches on the Remote Transmitter and Remote
Receiver to the same settings. This must be done so the
units will communcate properly. If you have other fans you	If using the light kit find wires from light and
can set to control from one transmitter by setting both	fan body. Plug wires together as follows.
receivers the same as the transmitter. If you have more	Connect blue wire from fan to black wire from
than one fan with remote. You can set the dip switches to	light. Connect white wire from fan to white wire
different positiosns to have seperate control.	from light.

Step Ladder

3

Install the Mounting Bracket to the Outlet box.

Use only the screws provided with the out- let box.

6

Slotted fitter arms

Use caution with the sloted fitter arms, do not force the fitter arms in assembling when using the light kit. Screw in the 2 allen screws then place switch housing cap with slots as shown on the 2 screws and twist.