7 
8 
|
| Take the last allen screw and align with hole in |
|
| Loosen the 3 screws with slots and remove the other |
| ||||||||
|
|
|
|
| ||||||||||
|
| the switch housing cap or light kit, then tighten |
|
| 3 screws. Save the screws. |
| ||||||||
|
| all 3 allen screws securely. |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 10 |
|
|
|
|
| 11 |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| Label | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| Use this label on the fan body for the first blade arm |
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| starting position. Use caution with blade arms and |
|
| |||
|
|
| Place medallion on | side of blade not marked |
| blades. Any pressure on blade arms or blades |
|
| ||||||
|
|
|
| |||||||||||
|
|
| this side up. Flip the blade over and attach |
| such as holding fan by blades or blade arms can |
|
| |||||||
|
|
| short arm to set of holes that are closest to the |
| create problems of blade pitch deviation or |
|
| |||||||
|
|
| corner of the blade. The remaining set of holes |
| deforming blade arms. |
|
| |||||||
|
|
| is for the long arm. Repeat for each blade. |
|
|
|
|
|
|
| ||||
|
| 13 |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| 14 |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Place medallion in blade for long blade arm. |
When attaching the second blade and arm to | Repeat for each blade. |
fan it should go under the first blade as shown |
|
in photo. Repeat for the other blades and arms. |
|
16 | 17 |
|
|
|
|
|
|
|
| Attach the long blade arms to motor after attach- |
| Thread wires and safety cable through motor cover. |
| ||
|
|
| ||||
|
|
|
|
| ||
| ing to blade. Tighten screws to motor securely |
|
|
|
| |
| and repeat for each blade arm. Caution go back |
|
|
|
| |
| and securely tighen screws in step 15. |
|
|
|
| |
9
To remove the top motor cover twist the cover and remove this will allow acesss to the screw holes for the blade arms.
12
Place blade arm over label on the fan body and tighten the 2 screws in the blade arm to the fan body.
15
Attach long blade arm to medallion with 2 screws, only start screws. Repeat for each long blade arm.
18
Place motor cover over 3 screws and twist cover into position. Take 3 screws removed ear- lier and replace, tighten all 6 screws securely.
