Installation
SAFETY TIPS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70- 1999), including
Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the
Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blade.
WARNING – Risk of fire, electric shock, or personal injury, The fan in this box may be either directly supported from a structural framing member of a building and/or may be mounted to an outlet box marked acceptable for fan support of 31.8 kg. (70 lbs.) or less. Most outlet boxes commonly used for the support of luminaires may not be acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
NEVER place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of
15. Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
Note - For Outdoor Fans Only: Suitable for use in damp locations when installed in a GFCI protected branch circuit.
Phillips Screwdriver | Wire Cutters | Pliers |
1 | 2 | OUTLET BOX METHOD |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
| fire, electric shock, or person- | ||||||||||
|
|
|
|
|
|
| ||||||||||
|
| Before you begin installing the fan, Switch |
| al injury. The fan in this box may be either |
| |||||||||||
|
|
| ||||||||||||||
|
| power off at Service panel and lock service dis- |
| directly supported from a structural framing |
| |||||||||||
|
| connecting means to prevent power from being |
| member of a building and/or may be mounted |
| |||||||||||
|
| switched on accidentally. When the service dis- |
| to an outlet box marked acceptable for fan sup- |
| |||||||||||
|
| connecting means cannot be locked, securely |
| port of of 31.8 kg (70 lbs) or less. Most outlet |
| |||||||||||
|
| fasten a prominent warning device, such as a |
| boxes commonly used for the support of lummi- |
| |||||||||||
|
| tag, to the service panel. |
| naires may not be acceptable for fan support |
| |||||||||||
|
|
| and may need to be replaced. Consult a quali- |
| ||||||||||||
|
|
|
|
|
| fied electrician if in doubt. |
|
|
|
|
|
| ||||
| 4 |
|
|
| 5 |
| BUILDING STRUCTURE METHOD |
|
|
| ||||||
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
| Mounting |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| Outlet box |
| Plate |
|
|
|
| |||
|
|
|
|
|
|
|
| Wood |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| Screws |
|
|
|
|
|
|
| |
|
| Remove the 4 screws attaching the Mounting |
|
| Secure mounting plate directly to a joist from |
|
| |||||||||
|
|
|
|
|
| |||||||||||
|
| neck the mounting plate. Retain the 4 screws |
|
| the buliding structure via the two knock out |
| ||||||||||
|
|
|
| holes on the outlet box. Use only the appropri- |
| |||||||||||
|
| for |
|
| ate wood screws and washers included with |
| ||||||||||
|
|
|
|
|
| your fan. Caution: Wood screws must go |
| |||||||||
|
|
|
|
|
| through into the building joist. |
| |||||||||
|
|
|
|
|
|
| ||||||||||
Step Ladder
3
Remove Safety bar from mounting bracket by loosing screws, sliding bar to side, and lifting it off the 2 screws.
6 | FAN BRACE AND BOX METHOD |
Install the mounting Plate to approved fan brace and box combination use only the hard- ware provided with the fan brace and box.
