Manuals / Motorola / Portable Media / Portable Radio

Motorola AP 73 user manual Alert Tone Indicators

Models: AP 73

1 85

Download 85 pages 36.58 Kb

Page 68

Alert Tone Indicators

Alert Tone Indicators

Successful Power-Up

A short, high-pitched tone when the radio is turned on indicates that the radio has passed its power-up self- test and is ready for use.

Unsuccessful Power-Up

A short, low-pitched tone immediately following the Successful Power-Uptone indicates that the radio has detected an error and has failed to power-up properly.

Valid Button Press

A short, high-pitched tone indicates that the last button pressed was valid.

Invalid Button Press

A short, low-pitched tone indicates that the last button pressed was invalid.

Low Battery

Three low-pitched tones indicate a low battery condi- tion.

DTMF Sidetones

Each DTMF tone is heard as it is transmitted.

Time-Out Timer Alert

A low-pitched continuous tone indicates that your present transmission has been disabled.

60	2-Year Warranty

Image 68

Motorola AP 73 user manual Alert Tone Indicators

Contents

Portable Radios AP73 Quick Reference Basic OperationMHz Operation Individual Call, , Group Call, or All Call SPM Dis- SPM Browse Menu Year Limited Warranty For Radios Step Copyright Information Contents Introduction Coverage of this User GuidePacking Information Radio Antenna Antenna Adaptor Spring Belt ClipKnobs, Buttons, Connectors and Others Signal Button Low Power / Frequency Step ButtonPush-To-Talk PTT Button Squelch / PL ButtonMode / Backspace Button Accessory ConnectorSpeaker Left Scroll / Offset ButtonEnable / Disable PTT ID Key Battery PackBattery Latches Numeric KeypadInstalling and Removing Batteries Getting StartedAttaching and Removing the Antenna Attaching and Removing the Belt ClipCharging NiCd Battery Pack Charging your Battery for the First time Length of time required to fully charge a new batteryCharging your Battery Subsequently Length of time required to fully recharge a used battery➊ Make sure the battery pack is attached to the radio Charging with Wall ChargerCharging with Desktop Charger ➊ Place the Charger Insert into the Desktop Charger➋ Insert the radio / battery into the charging docket Adjusting the Volume High / Low Power OutputBasic Operations Turning the Radio OnTransmitting a Message Receiving a Message Display Backlight Press and hold to enable / disable PTT IDAdditional Operations Locking / Unlocking the Radio’s Function Changing Squelch ModesCtcss Setting Squelch Level Selecting The Receive PL / DPL Squelch Code ➊Press and holdSelecting a Transmit PL / DPL Squelch Code ➋P ressReceive And Transmit PL / DPL Code Tables RPL.xxx PL Freq Equiv TPL.xxx PL CodeEquiv MHz Mode Operations Selecting MHz ModeSelecting the Frequency Step Size ➊Press and holdSelecting a Receive Frequency Enter the desired frequencyIi Through The Selector Knob CombinationTo ﬂash takes about 3 seconds Selecting The TX OffsetProgramming a User-Deﬁned TX Frequency MHz Mode Operations MHz Mode Operations Memory Mode Operations Selecting Memory ModeSelecting a Memory Channel Rotate the Selector Knob 2 to the desired chan- nel numberProgramming a Memory Channel Loading a Memory Channel Scan Operations Programmable Band Scan➊Press Frequency rangeRotate the Selector Knob 2 anti-clockwise ➋PressTransmitting During Band Scanning Pressing Push-To-Talk PTT Button 6, a digit onMemory Channel Scan BeforePress D Press Push-To-Talk PTT Button 6 to talk, release to listenScan Operations Dtmf Telephone Interconnect Placing a Telephone CallPress Stores the preprogrammed telephone numberLast Number Redial Storing a Phone NumberPress and hold Push-To-Talk PTT Button Then pressIf you make a mistake, press To scroll the cursor to the left or rightDisplaying a Stored Phone Number Voice Selective Call Optional Receiving a Voice Selective CallSending a Voice Selective Call Programmed see Edit Selective Call IDs onSpecial Programming Mode SPM Entering SPMExiting SPM Turn off the radio to exit SPMSPM Browse Menu Editing SPM Parameters Editing the Channel Scan ListTo scroll through the channels Erase a Single Channel from Memory➋ Press Editing the Phone Access / Deaccess CodesTo enter the edit mode Edit PTT ID ➊ In SPM, rotate the Selector Knob 2 to the PTT IDIng PTT ID Edit Selective Call IDs Editing Time Out Timer Setting the Selective Call Tone Status➋ Use To change the current statusSetting the Sidetones Status To toggle between On and OffSetting the Alert Tone Volume Setting the Battery Saver Status➋ Use OFS Options To scroll through the threeSetting the Battery Type Setting the Accessory Sense Option➊ In SPM, rotate the Selector Knob 2 to the Set To scroll through the optionsFactory Reset Feature Special Programming Mode SPM Indicators with Segments LCD Segments and IndicatorsIndicators Alert Tone Indicators Individual Selective Call Decode Acknowledgment ID DecodeGroup and All Call Selective Call Decode Nuisance Channel DeleteFor Portable Two-way Radios Information For Safe, Efﬁcient Opera- tionExposure To Radio Frequency Energy Electromagnetic Interference/compatibility Potentially Explosive AtmospheresBlasting Caps And Areas For Vehicles With An Air BagRecycling / Disposal of NiCd Batteries United StatesEurope AsiaJapan Licensing Licensing & Service InformationService Radio is dead TroubleshootingNiCd battery does not charge or last long enough Solution Clean battery and charger contacts often Alkaline Battery does not last long enough 10 minutesSolution Use proper radio etiquette Radio will not talk to other radios in systemHearing other conversations or noise on your radio Limited talk rangeYou have tried a solution for any of the above symp You hear constant static from speakerToms, without success Antennas AccessoriesBattery & Charging Accessories Radio to Radio Cloning Accessory Audio & Signalling Accessories for all modelsCarrying Cases & Accessories Limited Warranty Motorola Radio Products Receiver Radio SpeciﬁcationsGeneral Transmitter