Manuals
/
Brands
/
Computer Equipment
/
Mouse
/
MRV Communications
/
Computer Equipment
/
Mouse
MRV Communications
TS5000/4U1/V*), TS5000/ETH/V*, TS5000/XXX (TS5000G/XYZ/V**, TS5000/XYZ/V**
- page 77
1
77
87
87
Download
87 pages, 2.25 Mb
Contents
Main
TS5000/XXX
Installation Manual
Installation Manual
February 2008
Table of Contents
Page
Page
Standards
Standards Compliance
FCC Notice
CE Mark
Other Standards
MRV Laser Safety Certification
Disclaimer
Trademarks
Copyright 2007 by MRV
About this Installation Manual
Audience
Qualifications
Training
Experience
Safety Requirements
Before Installing
Before Powering On
Servicing
Introduction
CAREFULLY READ THE ENTIRE MANUAL BEFORE INSTALLING
A
The Product
.
Models
TS5000/155 TS5000/XYZ/V**
TS5000/M3C/V1S
TS5000/M3C/F1S
TS5000/155-F TS5000/XYZ/F**
TS5000/ETH TS5000/ETH/V*
1. Front
Transmitter
Receiver
2. Back
TS5000/G and TS5000/155
REMOTE MONITOR
(BACK VIEW)
TX RX
N
p
Telescope
g
Page
Selectors (DIP Switch DS1 Toggles)
Selectors (DIP Switch DS2 Toggles)
Indicators (7-segment display and LEDs)
REMOTE MONITOR
(BACK VIEW)
REDUNDANT
FOR FUSION
B. TS5000/G-F (Standard Model including Fusion option)
N
For more details please see pages 15 and 16
Pluggable interface, with Fusion option
Telescope
C. TS5000/155
Connectors
Note:
Slot for Power Supply
Alignment Telescope
Selectors (DIP Switch DS1 Toggles)
Selectors (DIP Switch DS2 Toggles)
Indicators (7-segment display and LEDs)
REMOTE MONITOR
(BACK VIEW)
REDUNDANT
FOR FUSION
D. TS5000/155-F (Standard Model including Fusion option)
ith a redundant power supply Panel Schematic
w
Figure 1.6: TS5000/155-F
Fusion Operation Mode
RF Transce
i
ver
RF Transce
Fusion
E. TS5000/ETH - Ethernet System
Page
F. TS5000/4U1 - 4E1 or 4T1 System
Dip switch setting Every DIP switch is set up for the channel above it.
Loop and Remote Loop Operation Mode
Heating
Monitoring and Management options
Typical Connection
IT IS A CROSS CONNECTION: TX RX AND RX TX
Site Survey
Line of Sight
Orientation
Location & Range
Page
Page
Mounting Environment & Stability
Page
Transmitting through a Window
Infrastructure
Power
Data/Signal Cabling
HANDLE THE FIBERS VERY CAREFULLY.
Bench Test
1 - TS5000/G & TS5000/G-F
2 - TS5000/155 & TS5000/155-F
3 - TS5000/ETH
Testing equipment
Setup
4 - TS5000/4U1
Compatibility
Testing equipment
Dip-switch Setup
Test Configurations
IR link
UWIN RX
BER Tester TXRX
TS T
S
TS TS
Display and Results
Proper Display
Expected Results
Proper Display
3. TS5000/ETH
4. TS5000/4U1 (4E1 or 4T1)
Proper Display
Expected Results
SNMP Management Setting and Operation
Installation
Accessories
Page
Alignment Knobs
The Installer Tool Kit (JITK-8)
Mounting 1- Accessories
2- Attachment of the Transceiver (TS)
Figure 5.9: JMP on the fixation surface
H
H
Page
Aiming Procedure
Powering on the TereScope
Transceiver Alignment
Action Screws Position Description Notes 1. Coarse Alignment
2. Fine Alignment
3. Tightening the Screws
4. Finishing the Alignment
Fine Alignment
not
Link Operating Test
IT IS A CROSS CONNECTION: TX RX AND RX TX
Installation Log
Before Closing the Rear Door
Page
Maintenance
Periodic Visits
APPENDIX A
Product Specifications
TS5000/G
TS5000/155 and TS5000/155-F
TS5000/ETH
TS5000/4U1 (4E1 or 4T1)
Digital Readout vs. Distance
APPENDIX B
Unpacking Instructions for TS4000/5000
APPENDIX C
Tool Kit, Equipment and Materials
APPENDIX D
6.
Page
TereScopes Bench Test Procedure
APPENDIX E
Page
Page
Page
Page
Effect of Wind on Terescope Devices
APPENDIX F
Appendix G
Page
Page
APPENDIX H
Page
Page
Page
APPENDIX I
Power Supply Replacement
General
Procedure
APPENDIX J
TS5000/155 and TS4000/155 enhancements