SECTION 3: ASSEMBLY INSTRUCTIONS

On some units, the D-handle may be pre-installed, requiring only loosening screws and some adjustment. If this is the case, go to step 4.

Installing and Adjusting the D-handle

1.Remove the screws and bottom clamp piece that were installed on the D-handle for shipping.

2.Place D-handle the over the shaft housing and onto the bottom clamp. See Figure 1. Place it a minimum of 6 inches (15.24 cm) from the end of the shaft grip.

3.Start screws with a large Flat-head or T-25 Torx screwdriver. Do not tighten until you make the handle adjustment.

4.If it was pre-installed, loosen the screws on the D-handle just enough to move the D-handle.

Shaft Grip

(4) Screws

Shaft

Housing

On/Off Stop Control

Minimum 6 inches

(15.24 cm)

D-Handle

Bottom Clamp

Figure 1

5.While holding the unit in the operating position, move the D-handle to the location that provides you the best grip. See Figure 2.

6.Tighten the clamp screws evenly, until the D-handle is secure.

Installing the Cutting Attachment Shield

Use the following instructions if the cutting attachment shield on your unit is not installed.

WARNING: To prevent serious personal injury, never operate the trimmer without the cutting attachment shield in place.

1.Slide the cutting attachment shield into the shield mount on the cutting attachment. Align the screw holes in the shield with the holes in the cutting attachment. See Figure 3.

2.Place a hex lock nut into one of the three recessed holes on the top of the cutting attachment shield. See Figure 4.

3.Install a screw into the hole from the bottom of the cutting attachment shield and screw it into the nut installed in step 2. See Figure 5. Do not tighten.

4.Repeat steps 2 and 3 until all three screws have been started, then tighten securely.

Shaft Housing

Cutting Attachment

Shield

Shield Mount

Cutting Attachment

Figure 3

Cutting Attachment

Shield

Recessed Holes

Hex Lock Nut

Figure 4

Screws (3)

Figure 2

Figure 5

7

Page 6 Page 8
Page 7
Image 7
MTD YM75 manual Installing and Adjusting the D-handle, Assembly Instructions
Page 6 Page 8

YM75 specifications

The MTD YM75 is a compact and efficient tractor designed for a variety of agricultural and landscaping tasks. Known for its versatility and robust performance, the YM75 is favored by many small-scale farmers and landowners looking to enhance their productivity.

One of the standout features of the MTD YM75 is its powerful engine. The tractor is equipped with a reliable diesel engine that has a displacement of 1.7 liters, delivering around 75 horsepower. This impressive power allows the YM75 to tackle tough tasks such as plowing, tilling, and hauling materials with ease. The efficiency of its engine not only provides ample power but also ensures lower fuel consumption, making it economical for long-term use.

The MTD YM75 incorporates advanced technologies that make it user-friendly and efficient. The tractor features a synchronized transmission system, allowing for smooth gear shifts and precise control over speed and torque. This is particularly beneficial when operating various implements or navigating challenging terrains. Additionally, the tractor's compact design enables it to maneuver effortlessly in tight spaces, making it suitable for small farms and gardens.

The hydraulic system of the YM75 is another highlight, boasting a high lifting capacity. This enables the attachment of various implements, such as front loaders, backhoes, and other tools, enhancing the tractor's versatility. The hydraulic setup is designed to be responsive, providing operators with the ability to control attachments with precision.

In terms of operator comfort, the MTD YM75 does not disappoint. It features an ergonomic cabin with adjustable seating, providing a comfortable driving experience even during long working hours. The controls are intuitively placed, allowing for easy access and minimizing distractions while operating the machinery.

Durability is a key characteristic of the MTD YM75. Built with high-quality materials and robust construction, this tractor is designed to withstand the rigors of daily agricultural work. Its rugged tires ensure excellent traction and stability on various terrains, contributing to its overall reliability.

In summary, the MTD YM75 is a powerful, versatile, and user-friendly tractor that meets the needs of modern farmers and landscapers. With its efficient engine, advanced hydraulic system, ergonomic design, and durability, it stands out as an excellent choice for enhancing productivity in any agricultural setting. Whether for tilling the land or managing landscaping projects, the YM75 proves to be an invaluable asset.
Top Page Image Contents