installation

Outdoor Installation

If possible install the generator in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generator is on secure level ground so that it cannot slide or shift around.

The installation site must be relatively free from moisture and dust. All electrical equipment should be protected from excessive moisture. Failure to do will result in deterioration of the insulation and will result in short circuits and grounding.

Foreign materials such as dust, sand, lint and abrasive materials have a tendency to cause excessive wear to engine and alternator parts.

WARNING

Pay close attention to ventilation when operating the generator inside tunnels and caves. The engine exhaust contains noxious elements. Engine exhaust must be routed to a ventilated area

Indoor Installation

Exhaust gases from gas engines are extremely poisonous. Whenever an engine is installed indoors the exhaust fumes must be vented to the outside. The engine should be installed at least two feet from any outside wall. Using an exhaust pipe which is too long or too small can cause excessive back pressure which will cause the engine to heat excessively and possibly burn the valves.

placement

The generator should always be placed on a flat level surface when it is running. DO NOT place the generator on slopes, the possibility exists that the generator could slide.

DANGER

An electric shock is apt to happen when vibrators are used. Pay close attention to handling when operating vibrators and always use rubber boots and gloves to insulate the body from a short circuit.

Generator Grounding

To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground.

Article 250 (Grounding) of the National Electrical Code (NEC) provides guide lines for proper grounding and specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

NEC articles 250-64(b) and 250-66 set the following grounding requirements:

1.Use one of the following wire types to connect the generator to earth ground.

a.Copper - 10 AWG (5.3 mm2) or larger.

b.Aluminum - 8 AWG (8.4 mm2) or larger.

2.When grounding the generator (Figure 2) connect the ground cable between the lock washer and the nut on the generator and tighten the nut fully. Connect the other end of the ground cable to earth ground.

3.NEC article 250-52(c) specifies that the earth ground rod should be buried a minimum of 8 ft. into the ground.

NOTICE

When connecting the generator to any buildings electrical system ALWAYS consult with a licensed electrician.

GA6HB/6HEB 60 hz GENERATOR • operation and parts manual — rev. #0 (03/13/14) — page 15

Page 14 Page 16
Page 15
Image 15
Multiquip ga6HB, ga6HEB manual Outdoor Installation, Indoor Installation, Placement, Generator Grounding
Page 14 Page 16

ga6HB, ga6HEB specifications

Multiquip has established itself as a leading manufacturer of innovative and reliable construction equipment. Among its impressive lineup, the GA6HEB and GA6HB generators stand out due to their advanced features and exceptional performance. Both models cater to a variety of applications, making them suitable for construction sites, events, and emergency power needs.

The GA6HEB generator is equipped with a powerful 6 kW output capability, which makes it ideal for powering tools and equipment in demanding environments. For those looking for a more efficient alternative, the GA6HB offers similar power with a focus on convenience and ease of use. Both units utilize a highly efficient engine, ensuring that fuel consumption is minimized while still delivering reliable power when needed.

One of the defining features of the GA6HEB and GA6HB is their innovative design. Constructed with high-quality materials, these generators are built to withstand the rigors of daily use. Their robust frames provide enhanced durability, ensuring longevity in harsh job site conditions. Additionally, the compact design of both models allows for easy transport and storage, making them a practical choice for contractors and event planners alike.

In terms of technology, these generators include advanced control systems that enhance usability. The user-friendly interface provides operators with vital information at a glance, including voltage output, hour meters, and maintenance reminders. This focus on intuitive operation ensures that even those with minimal experience can efficiently manage these units.

Noise reduction technology is another significant characteristic of the GA6HEB and GA6HB. These generators are designed to operate quietly, allowing for use in noise-sensitive environments without disturbing nearby activities. This feature is particularly beneficial for outdoor events and residential applications, where peace and tranquility are paramount.

Fuel efficiency and runtime are critical for users, and both models deliver impressive performance in this regard. With extended run times on a single tank of fuel, the GA6HEB and GA6HB are perfect for long-term projects where consistent power is needed without frequent refueling.

Overall, the Multiquip GA6HEB and GA6HB generators are exemplary choices for various power needs. Their combination of robust construction, advanced technology, and user-friendly design makes them valuable assets for any project requiring reliable and efficient power solutions. Whether for professional contractors or casual users, these models promise the performance and dependability that Multiquip is renowned for.
Top Page Image Contents