Multiquip MVC-64E/EW Maintenance, Inspection and Maintenance ServiceTables, Daily Service

CAUTION

Inspection and other services should always be carried out on hard and level ground with the engine shut down.

Inspection and Maintenance ServiceTables.

1.To make sure your plate compactor is always in good working condition before using, carry out the maintenance inspection in accordance with Tables 5 through 7.

TABLE 5. MVH-64E/EW MACHINE INSPECTION

ITEM					HOURS OF OPERATION
Damaged Parts					Every 8 hours (every day)
Loose or Lost Screws					Every 8 hours (every day)
Function of Controlling System					Every 8 hours (every day)
Part
Vibrator Oil Check					Every 100 hours
Vibrator Oil Replacement					Every 300 hours
V-belt (clutch) Check					Every 200 hours
	Table 6. ENGINE MAINTENANCE
			FIRST	EVERY 3		EVERY 6	EVERY	EVERY
DESCRIPTION (3)	OPERATION	BEFORE	MONTH		MONTHS	MONTHS	YEAR	2 YEARS
			OR		OR	OR	OR	OR
			10 HRS.		25 HRS.	50 HRS.	100 HRS.	200 HRS.
Engine Oil	CHECK	X
	CHANGE		X
Air Cleaner	CHECK	X
	CHANGE				X (1)
All Nuts & Bolts	Re-tighten If	X
	Necessary
Spark Plug	CHECK-CLEAN					X
	REPLACE							X
Cooling Fins	CHECK					X
Spark Arrester	CLEAN						X
Fuel Tank	CLEAN						X
Fuel Filter	CHECK						X
Idle Speed	CHECK-ADJUST						X (2)
Valve Clearance	CHECK-ADJUST							X (2)
Fuel lines	CHECK			Every 2 years (replace if necessary) (2)

(1)Service more frequently when used in DUSTY areas.

(2)These items should be serviced by your servic dealer, unless you have the proper tools and are mechanically proficient. Refer to the ROBIN Manual for service procedures

(3)For commercial use, log hours of operation to determine proper maintenance intervals.

MVC-64E/EW — MAINTENANCE

CAUTION

These inspection intervals are for operation under normal conditions. Adjust your inspection intervals based on the number hours plate compactor is in use, and particular working conditions.

CAUTION

Fuel piping and connections should be replaced every 2 years.

Daily Service

zCheck for leakage of fuel or oil.

zRemove soil and clean the bottom of compaction plate.

zCheck engine oil, see page 16.

zCheck for loose screws including tightness. See Table 7 below (tightening torque ), for retightening:

TABLE 7.

TIGHTENING TORQUE (in. kg/cm) Diameter

Material	6mm	8mm	10mm	12mm	14mm	16mm	18mm	20mm
4T	70	150	300	500	750	1,100	1,400	2,000
6-8T	100	250	500	800	1,300	2,000	2,700	3,800
11T	150	400	800	1,200	2,000	2,900	4,200	5,600

*100 (6mm) 300 ~ 350 (8mm) 650 ~ 700 (10mm)

*(In case counter-part is of aluminum)

(Threads in use with this machine are all right handed)

Material and quality of material is marked on each bolt, and screw.

ENGINE OIL

1.Drain the engine oil when the oil is warm as shown in Figure 22.

2.Remove the oil drain bolt and sealing washer and allow the oil to drain into a suitable container.

3.Replace engine oil with recommended type oil as listed inTable 4.Engine oil capacity is .634 quarts (.6 liters).DO NOT overfill.

4.Install drain bolt with sealing washer and tighten se- curely.

MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 21