BEARING BRACKET

Grease the bearing bracket every month.

COUNTERSHAFT

The countershaft rotates on two self-aligned pillow block bearings. Grease these every 40 hours using grade #1 Lithium Base grease.

GEAR ALIGNMENT

The countershaft and driven pinion are mounted on a slotted base.To align gears, loosen the pillow block mounting bolts and move them until the necessary alignment has been made.

GEAR LUBRICATION

The surface of the pinion and the bull gear should be very lightly greased every 250 hours.

IMPORTANT! AVOID OVER-GREASING.

EXCESS GREASE WILL ACCUMULATE

CONTAMINATES AND CAUSE PREMATURE

WEAR.

IMPORTANT — DRUM HEAD SEAL CARE

Grease seals every 40 hours of operation using any grade #1 lithium base grease. Apply grease until visible inside of mixing tub (overgrease). This will purge seal system of contamination.

DRUM GRILL

The drum opening is covered by a steel grill that is hinged for easy cleaning.This grill should be closed at all times when mixer is in use. Do not remove the grill or grill opening bar. Keep the grill clean by washing it down daily.

CAUTION: Stop the engine before allowing anybody to put their hands in the mixing drum.

TOWING — Before towing, check with local and state laws for proper compliance.

The tow bar and chain must be properly attached to the mixer and towing vehicle prior to towing. Refer to the following installation instruction:

Step 1. Insert the Draw Bar into the main frame. Secure, utilizing the ¾" bolt (grade 5) and nylock nut.Tighten to 100 foot pounds.

Step 2. Install the chain through the hole located between the frame gusset and frame angle. Loop the chain together and place under the Draw Bar. Secure with connector link.

Step 3. Extend the chain along the length of the Draw Bar, remove excess chain (slack) and secure to bottom connector link. Secure the chain to the towing vehicle, using the connector link.

WM-900S, 900P — OPERATIONS

NOTE: It is critical that the length of chain be properly adjusted to prevent the Draw Bar and front mixer stand from dropping to the ground (contact) in the event the Draw Bar becomes disconnected from the towing vehicle.

STEP 1

DRAW BAR

BOLT & NUT

INSERT CHAIN THROUGH

STEP 2

THE HOLE

 

 

DRAW BAR

FRAME ANGLE

 

FRAME GUSSET

CONNECTOR LINK

STEP 3

VEHICLE

CONNECTOR LINK

DRAW BAR

REMOVE EXCESS

CHAIN (SLACK)

BOTTOM CONNECTOR LINK

SAFETY CHAIN

P/N 3148

CONNECTOR LINK

P/N 01004

WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 9

Page 9
Image 9
Multiquip WM-900P operation manual WM-900S, 900P Operations

WM-900S, WM-900P specifications

The Multiquip WM-900P and WM-900S are robust and reliable water pumps designed to cater to a wide range of applications, including construction sites, dewatering tasks, and emergency situations. Both models are part of Multiquip's commitment to providing high-quality equipment tailored for performance, efficiency, and longevity.

The WM-900P is a powerful semi-trash pump that excels in handling muddy and debris-laden water. It is equipped with a 9 HP Honda GX270 engine, which delivers exceptional performance and efficiency. This pump is capable of moving up to 9,600 gallons of water per hour, making it suitable for significant dewatering tasks. Its cast iron volute and impeller provide enhanced durability and resistance to wear, ensuring a longer lifespan even when dealing with abrasive materials.

On the other hand, the WM-900S is a self-priming water pump that offers versatile usage for clear water applications. It is powered by a robust 9 HP engine like its counterpart but is specifically designed to handle clean or slightly dirty water. This model can pump up to 8,400 gallons per hour, making it ideal for household and light industrial applications, irrigation, or swimming pool filling.

Both models feature an easy-access clean-out port, which simplifies maintenance and ensures optimal performance over time. The sturdy frames are designed for portability, equipped with large, puncture-resistant wheels that allow for easy transport across job sites. The pumps also come with a protective frame to safeguard against damage while in transit or in use.

Technologically, the WM-900P and WM-900S incorporate advanced self-priming mechanisms, guaranteeing quick setup and operational readiness. Anti-vibration mounts help reduce noise and provide a more stable operation, which is especially advantageous in residential areas or sensitive environments.

Safety features are also integral to the design of these pumps. Equipped with low-oil shutdown sensors, these pumps prevent engine damage by automatically shutting off when oil levels drop too low. This feature not only enhances the durability of the units but also provides peace of mind to operators.

In summary, the Multiquip WM-900P and WM-900S are expertly designed water pumps that combine performance, efficiency, and durability. Their powerful engines, effective pumping capabilities, and user-friendly features make them indispensable tools for numerous water management tasks, making them a valuable addition to any contractor’s or homeowner’s equipment lineup.