Result Code Options, Modem Reset | Multitech MT5634ZBA-USB instruction

MT5634ZBA-USB User Guide

Command: Vn Result Code Format
Values:	n = 0 or 1
Default:	1
Description:V0	Displays result codes as digits (terse response).
V1	Displays result codes as words (verbose response).

Command: Wn	Result Code Options
Values:	n = 0, 1, or 2
Default:	2
Description:W0	CONNECT result code reports serial port speed, disables protocol result codes.
W1	CONNECT result code reports serial port speed, enables protocol result codes.
W2	CONNECT result code reports line speed, enables protocol result codes.

Command: Xn Result Code Selection
Values:	n = 0–7
Default:	4
Description:X0	Basic result codes (e.g., CONNECT); does not look for dial tone or busy signal.
X1	Extended result codes (e.g., CONNECT 46000 V42bis); does not look for dial tone or busy
	signal.
X2	Extended result codes with NO DIALTONE; does not look for busy signal.
X3	Extended result codes with BUSY; does not look for dial tone.
X4	Extended result codes with NO DIALTONE and BUSY.
X5	Extended result codes with NO DIALTONE and BUSY.
X6	Extended result codes with NO DIALTONE and BUSY.
X7	Basic result codes with NO DIALTONE and BUSY.

Command: Yn Long Space Disconnect
Values:	n = 0
Default:	0
Description:Y0	Disable sending or responding to long space break signal on disconnect.
Y1	Enable sending or responding to long space break signal on disconnect. (Not supported.)

Command: Zn	Modem Reset
Values:	n = 0 or 1
Default:	None
Description:Z0	Reset modem to profile saved by the last &W command.
Z1	Same as Z0.
Command: &Bn	V.32 Auto Retrain
Values:	n = 1
Default:	1
Description:&B0	Disable V.32 auto retrain. (Not supported.)
&B1	Enable V.32 auto retrain.
Command: &Cn	Data Carrier Detect (DCD) Control
Values:	n = 0 or 1
Default:	1
Description:&C0	Forces the DCD circuit to be always high.
&C1	DCD goes high when the remote modem’s carrier signal is detected, and goes low when
	the carrier signal is not detected.

26

Image 26

Multitech MT5634ZBA-USB User Guide Command Vn Result Code Format, Result Code Options, Command Xn Result Code Selection

Contents

User Guide Record of Revisions Trademarks Contents Index Introduction and Description Universal Serial Bus USB IntroductionProduct Description MT5634ZBA-USB User Guide What Is in Your Modem Package? Introduction and Description MT5634ZBA-USB User Guide Quick Start We supply Safety WarningsWhat You Will Need You supply Assemble the Modem Quick Start Install the Software Phone Connection Connect the Modem to Your SystemLine Connection USB Connection Select the Modem Test Your Modem Features Data FeaturesWhat Can You Do with Your Modem? Computer FaxRequired Equipment Telephone Line Connecting to a Telephone Set Phone Connecting to the Computer USBConnecting to the Telephone Line Line Connections Front Panel Front panel MT5634ZBA-USB User Guide AT Commands, S-Registers and Result Codes AT Commands AT Command Summary Monitor Speaker Volume Command DS=n Dial Stored Telephone NumberEcho Command Mode Characters Echo Online Data Characters Result Codes Enable/Disable Monitor Speaker ModeReturn Online to Data Mode Command Sr=n Set Register Value Command Yn Long Space Disconnect MT5634ZBA-USB User Guide Command Vn Result Code FormatCommand Xn Result Code Selection Modem Reset Communications Mode Load Factory SettingsCommand &Gn V.22bis Guard Tone Control Asynchronous Communications Mode Command &Wn Store Current Configuration MT5634ZBA-USB User Guide Command &Tn V.54 Test CommandsDisplay Current Settings Select Stored Configuration for Hard Reset Data Buffer Control Error Correction Mode SelectionModem Port Flow Control Break Control Command %DCnAT Command Control Inactivity TimerCommand %Cn Data Compression Control Protocol Result Code Command #S=x Store Setup Password Command %En Fallback and Fall Forward ControlEnter Setup Password Command%%%ATCRRemote Configuration Escape Sequence Registers Rates K56flex Rates S37S38 S48 S42S43 S89 Result Codes Terse Verbose Description MT5634ZBA-USB User Guide Remote Configuration Changing the Setup Password Basic ProcedureSetup Remote Configuration Changing the Remote Escape Character MT5634ZBA-USB User Guide Troubleshooting None of the Indicators Light Modem Does Not Respond to Commands Troubleshooting Modem Dials But Cannot Connect Modem Doesn’t Work with Caller ID Modem Cannot Connect When AnsweringModem Disconnects While Online Fax and Data Software Can’t Run at the Same Time Appendixes Appendix a Regulatory Compliance FCC Regulations for Telephone Line Interconnection Class B Statement Industry Canada Canadian Limitations Notice FAX Branding Statement New Zealand Telecom Warning Notice European DirectivesInternational Modem Restrictions Appendix B Technical Specifications ITU-T ConnectorsCarrier Frequencies ITU-T V.32bis/V.32 Carrier Frequencies Dimensions DiagnosticsIndicators Weight Appendix C Loopback Tests Introduction Figure C-1. Local analog loopback test Test Procedure Local Analog Loopback Test V.54 Loop Remote Digital Loopback Test V.54 Loop Appendix C Loopback Tests Figure C-3. Local digital loopback test Test Procedure Local Digital Loopback Test V.54 Loop Online Warranty Registration Appendix D Warranty, Service, and Technical SupportLimited Warranty Service To Log on to the Multi-Tech BBS Technical SupportMulti-Tech BBS To Download a File About the Multi-Tech Fax-Back Service About the Internet Index Index MT5634ZBA-USB User Guide