Command DS=n Dial Stored Telephone Number | Multitech MT5634ZBA-USB

MT5634ZBA-USB User Guide

@Wait for quiet answer. Causes modem to wait for a ringback, then 5 seconds of silence, before processing next part of command. If silence is not detected, the modem returns a NO ANSWER code.

^Disable data calling tone transmission.

$ Detect AT&T call card “bong” tone. The character should follow the phone number and precede the user’s call card number: ATDT1028806127853500$123456789

Command: DS=n Dial Stored Telephone Number

Values:	n = 0–1
Default:	none
Description:	Dial a number previously stored in directory number y by the &Zy=x command.
	Example: ATDS=1
Command: En	Echo Command Mode Characters
Values:	n = 0 or 1
Default:	1
Description:E0	Do not echo keyboard input to the terminal.
E1	Do echo keyboard input to the terminal.
Command: Fn	Echo Online Data Characters
Values:	n = 1
Default:	1
Description:F0	Enable online data character echo. (Not supported.)
F1	Disable online data character echo (included for backward compatibility with some soft-
	ware).
Command: Hn	Hook Control
Values:	n = 0 or 1
Default:	0
Description:H0	Go on-hook (hang up).
H1	Go off-hook (make the phone line busy).
Command: In	Information Request
Values:	n = 0–5, 9, 11
Default:	None
Description:I0	Display default speed and controller firmware version.
I1	Calculate and display ROM checksum (e.g., 12AB).
I2	Check ROM and verify the checksum, displaying OK or ERROR.
I3	Display default speed and controller firmware version.
I4	Display firmware version for data pump (e.g., 94).
I5	Display the board ID: software version, hardware version, and country ID
I9	Display the country code (e.g., NA Ver. 1).
I11	Display diagnostic information for the last modem connection, such as DSP and firmware
	version, link type, line speed, serial speed, type of error correction/data compression, num-
	ber of past retrains, etc.
Command: Ln	Monitor Speaker Volume
Values:	n = 0, 1, 2, or 3
Default:	2
Description:L0	Select low volume.
L1	Select low volume.
L2	Select medium volume.
L3	Select high volume.

24

Image 24

Multitech MT5634ZBA-USB manual Command DS=n Dial Stored Telephone Number, Echo Command Mode Characters, Hook Control

Contents

User Guide Record of Revisions Trademarks Contents Index Introduction and Description Introduction Product DescriptionUniversal Serial Bus USB MT5634ZBA-USB User Guide What Is in Your Modem Package? Introduction and Description MT5634ZBA-USB User Guide Quick Start Safety Warnings What You Will NeedWe supply You supply Assemble the Modem Quick Start Install the Software Connect the Modem to Your System Line ConnectionPhone Connection USB Connection Select the Modem Test Your Modem Features Features What Can You Do with Your Modem?Data Fax Required EquipmentComputer Telephone Line Connecting to the Computer USB Connecting to the Telephone Line LineConnecting to a Telephone Set Phone Connections Front Panel Front panel MT5634ZBA-USB User Guide AT Commands, S-Registers and Result Codes AT Commands AT Command Summary Command DS=n Dial Stored Telephone Number Echo Command Mode CharactersMonitor Speaker Volume Echo Online Data Characters Monitor Speaker Mode Return Online to Data ModeResult Codes Enable/Disable Command Sr=n Set Register Value MT5634ZBA-USB User Guide Command Vn Result Code Format Command Xn Result Code SelectionCommand Yn Long Space Disconnect Modem Reset Load Factory Settings Command &Gn V.22bis Guard Tone ControlCommunications Mode Asynchronous Communications Mode MT5634ZBA-USB User Guide Command &Tn V.54 Test Commands Display Current SettingsCommand &Wn Store Current Configuration Select Stored Configuration for Hard Reset Error Correction Mode Selection Modem Port Flow ControlData Buffer Control Break Control Inactivity Timer Command %Cn Data Compression ControlCommand %DCnAT Command Control Protocol Result Code Command %En Fallback and Fall Forward Control Enter Setup PasswordCommand #S=x Store Setup Password Command%%%ATCRRemote Configuration Escape Sequence Registers S37 S38Rates K56flex Rates S42 S43S48 S89 Result Codes Terse Verbose Description MT5634ZBA-USB User Guide Remote Configuration Basic Procedure SetupChanging the Setup Password Remote Configuration Changing the Remote Escape Character MT5634ZBA-USB User Guide Troubleshooting None of the Indicators Light Modem Does Not Respond to Commands Troubleshooting Modem Dials But Cannot Connect Modem Cannot Connect When Answering Modem Disconnects While OnlineModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same Time Appendixes Appendix a Regulatory Compliance FCC Regulations for Telephone Line Interconnection Class B Statement Industry Canada Canadian Limitations Notice FAX Branding Statement European Directives International Modem RestrictionsNew Zealand Telecom Warning Notice Appendix B Technical Specifications Connectors Carrier FrequenciesITU-T ITU-T V.32bis/V.32 Carrier Frequencies Diagnostics IndicatorsDimensions Weight Appendix C Loopback Tests Introduction Figure C-1. Local analog loopback test Test Procedure Local Analog Loopback Test V.54 Loop Remote Digital Loopback Test V.54 Loop Appendix C Loopback Tests Figure C-3. Local digital loopback test Test Procedure Local Digital Loopback Test V.54 Loop Appendix D Warranty, Service, and Technical Support Limited WarrantyOnline Warranty Registration Service Technical Support Multi-Tech BBSTo Log on to the Multi-Tech BBS To Download a File About the Multi-Tech Fax-Back Service About the Internet Index Index MT5634ZBA-USB User Guide