ASSEMBLY
Read and follow the assembly and adjustment instructions for your snow thrower. All fasteners are in the parts bag. Do not discard any parts or material until the unit is assembled.
WARNING: Before doing any assembly or maintenance to the snow thrower, remove the wire
from the spark plug.
NOTE: In this instruction book, left and right describe the location of a part from the oper- ator’s position behind the unit.
NOTE: Torque is measured in foot pounds (metric N.m). This measurement describes how tight a nut or bolt must be. The torque is measured with a torque wrench.
NOTE: Illustrations begin on page 3.
NOTE: Fasteners and loose parts are shown at full size in Figure 27.
Tools Required
1 Knife
1Pliers
21/2 inch open end wrenches
29/16 inch open end wrenches
23/4 inch open end wrenches
1Measuring tape or ruler
1Screwdriver
How To Remove The Snow Thrower From The Carton
1.(Figure 1) The snow thrower is shown in the shipping position.
2.Cut and discard the plastic tie that secures the crank assembly.
3.Cut down all four corners of the carton and lay the side panels flat.
4.Locate all parts that are packed separately and remove from the carton.
5.Remove and discard the packing material from around the snow thrower.
6.(Figure 2) For shipping purposes, the height adjust skids (7) are attached to the pallet. Remove the screw (17) that secures each height adjust skid (7) to the pallet.
7.Hold onto the lower handle and pull the snow thrower off the pallet.
CAUTION: DO NOT back over cables.
8.Remove the packing material from the han- dle assembly.
9.Cut the ties that secure the clutch control cables (1) to the lower handle (2). Move the cables away from the motor frame.
How To Assemble The Handle And Crank Assembly
1.(Figure 3) Loosen, but do not remove, the fasteners (1) in the upper holes of the lower handle.
2.Remove the fasteners and the crank assem- bly eyebolt (11) from the lower holes of the lower handle.
3.(Figure 2) Put the shift lever (6) into first forward position.
4.(Figure 3) Raise the upper handle (2) to the operating position.
NOTE: Make sure the cables are not caught between the upper and lower han- dle.
5.Install the fasteners and the crank assembly eyebolt (11) that were removed in step 2. DO NOT tighten until all fasteners are in place.
6.(Figure 4) Attach the crank rod (15) to the universal joint assembly (16) with the hair pin (12).
7.(Figure 3) Tighten nut on eye bolt (11). Make sure eye bolt (11) is properly aligned and the crank (8) can freely rotate.
8.Tighten all handle fasteners.
Check The Cables
1.(Figure 5) Check the traction drive cable
(1)and the auger drive cable (2). If the bot- tom of the cables have become discon- nected, reinstall the cables.
2.(Figure 6) If the top of the cables (5) have become disconnected from the drive levers
(6), attach the cables (5) to the “Z” fitting
How To Set The Skid Height (Figure 2)
The snow thrower is equipped with height ad- justable skids (7) mounted on the outside of the auger housing (4). To adjust the height of the skids, see “How To Adjust The Height Of The Skids” in the Maintenance section.
How To Prepare The Engine
Note: The engine was shipped from the fac- tory filled with oil. Check the level of the oil. Add oil as needed. Engine does not contain
GASOLINE.
WARNING: Follow the engine manufacturer’s instructions for the type of fuel and oil to use. Always
use a safety fuel container. Do not smoke when adding gasoline to the engine. When inside an enclosure, do not fill with gaso- line. Before you add fuel, stop the engine. Let the engine cool for several minutes.
Check the oil. See the engine manufacturer’s instructions for the type of fuel and oil to use. Before you use the unit, read the information on safety, operation, maintenance, and storage.
Important! Before You Start Operating
rCheck the fasteners. Make sure all fas- teners are tight.
rOn electric start models, the unit was shipped with the starter cord plugged into the engine. Before operating, un- plug the starter cord from the engine.
rIf a bar code label is attached to the han- dle, remove before operating.
OPERATION
NOTE: Illustrations begin on page 3.
Know Your Snow Thrower (Figure 2)
Read this Instruction Book and safety rules be- fore operation the snow thrower. Compare the illustration with your snow thrower to familiarize yourself with the location of various controls and adjustments.
12
ENGLISH
Traction Drive Lever (1) - Select the forward or reverse direction of travel.
Crank Assembly (2) - Changes the direction of the discharge chute.
Discharge Chute (3) - Changes the distance the snow is thrown.
Auger Drive Lever (5) - Starts and stops the au- ger and impeller (snow gathering and throwing).
Speed Shift Lever (6) - Selects the speed of the snow thrower.
Height Adjust Skid (7) - Adjusts the ground clearance of the auger housing.
Ignition Key (8) - Must be inserted to start the en- gine.
Primer Button (9) - Injects fuel directly into the carburetor for fast starts in cold weather.
Electric Start Button (10) - On electric start mod- els, used to start the engine.
Switch Box (11) - On electric start models, used to attach a 120 volt electric power cord.
Recoil Starter Handle (12) - Use to manually start the engine.
Throttle Control (13) - Controls the speed of the engine.
Choke Control (14) - Use to start a cold engine.
How To Control
The Discharge Of The Snow
WARNING: Never direct the dis- charge of snow toward bystanders.
WARNING: Always stop the engine before unclogging the discharge chute or the auger housing and be-
fore leaving the snow thrower.
1.(Figure 2) Turn the crank assembly (2) to change the discharge direction of the snow.
2.(Figure 7) Loosen the wing knob (1) on the chute deflector (2).
3.Move the chute deflector (2) up for more distance or down for less distance.
4.Tighten the wing knob (1).
How To Stop
The Snow Thrower (Figure 2)
1.To stop discharging snow, release the auger drive lever (5).
2.To stop the wheels, release the traction drive lever (1).
3.To stop the engine, push the throttle control lever (13) to off and remove the ignition key
(8).
