Napoleon Fireplaces BGD48N, BGD48P Operation / Maintenance, Operating Instructions, Open windows

22

OPERATION / MAINTENANCE

OPERATING INSTRUCTIONS

When lit for the fi rst time, the fireplace will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing of the logs and the "burn-in" of internal paints and lubricants used in the manufacturing process and will not occur again.

After extended periods of non-operation such as following a vacation or a warm weather season, the fi replace may emit a slight odour for a few hours. This is caused by dust particles in the heat exchanger burning off. In both cases, open a window to suffi ciently ventilate the room.

Purge the gas line with the glass door removed. Assure that a continuous gas flow is at the burner before reinstalling the door.

FOR YOUR SAFETY READ BEFORE LIGHTING:

A. This fi replace is equipped with a pilot which must be lit by hand while following these instructions exactly.

B. Before operating smell all around the fi replace area for gas and next to the floor because some gas is heavier than air and will settle on the fl oor

C. Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try to repair it. Call a quali-

fi ed service technician. Force or attempted repair may result in a fi re or explosion.

D.Do not use this fi replace if any part has been under water. Imme- diately call a qualifi ed service technician to inspect the fi replace and replace any part of the control system and any gas control which has been under water.

WHAT TO DO IF YOU SMELL GAS

• Turn off all gas to the fi replace.

• Open windows. FIGURE 53

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neigh- GAS KNOB bour's phone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fi re department.

FIGURE 54

LIGHTING INSTRUCTIONS

WARNING: The gas valve has an interlock device which will not allow the pilot burner to be lit until the thermocouple has cooled. Allow approximately 60 seconds for the thermocouple to cool.

When lighting and relighting, the gas knob cannot be turned from pilot to off unless the knob is depressed slightly.

1.Stop! Read the above safety information on this label.

2.Turn off all electric power to the fi replace.

3.Turn the gas knob clockwise to off.

4.Wait five (5) minutes to clear out any gas. If you smell gas includ- ing near the fl oor. Stop! Follow "B" in the above safety information on this label. If you don't smell gas go the next step.

5. Turn gas knob counter-clockwise to pilot.

6.Depress slightly and hold gas knob while lighting the pilot with the push button igniter. Keep knob depressed for one minute, then release. If pilot does not continue to burn, repeat steps 3 through

7.With pilot lit, depress and turn gas knob counter-clockwise to

on.

8.If equipped with remote on-off switch/thermostat, main burner may not come on when you turn valve to on. Remote switch must be in the on position to ignite burner.

9.Turn on all electric power to the fi replace.

TO TURN OFF GAS

1.Turn off all electric power to the fi replace if service is to be 2. Push in gas control knob slightly and turn clockwise to off. Do

performed.	not force.
MAINTENANCE	3.	Check to see that all burner ports are burning. Clean out any of
Turn off the gas and electrical power before servicing the	the ports which may not be burning or are not burning properly.
fireplace.	4.	Check to see that the pilot fl ame is large enough to engulf the
CAUTION: Label all wires prior to disconnection when servicing	thermocouple and thermopile and reaches toward the burner with
controls. Wiring errors can cause improper and dangerous operation.	the third jet.
Verify proper operation after servicing. This fi replace and its venting	5.	Replace the cleaned logs.
system should be inspected before use and at least annually by a	6.	Check to see that the main burner ignites completely on all open-
qualifi ed service person. The fi replace area must be kept clear and	ings when the gas knob for the burner is turned on. A 5 to 10 second
free of combustible materials, gasoline or other fl ammable vapours	total light-up period is satisfactory. If ignition takes longer, consult
and liquids. The fl ow of combustion and ventilation air must not be	your Napoleon® dealer / distributor.
obstructed.	7.	Check that the gasketing on the sides, top and bottom of the door

is not broken or missing. Replace if necessary.

1. In order to properly clean the burner and pilot assembly, remove the logs to expose both assemblies.

2. Keep the control compartment, logs, burner, air shutter opening and the area surrounding the logs clean by vacuuming or brushing, at least once a year.

W415-0326 / C / 11.23.07